- 您現在的位置：買賣IC網 > PDF目錄368631 > TDA935X (NXP Semiconductors N.V.) TV signal processor-Teletext decoder with embedded m-Controller PDF資料下載
參數資料
| 型號： | TDA935X |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | TV signal processor-Teletext decoder with embedded m-Controller |
| 中文描述： | 電視信號處理器與嵌入式米圖文電視解碼器控制器 |
| 文件頁數： | 138/140頁 |
| 文件大?。?/td> | 570K |
| 代理商： | TDA935X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁當前第138頁第139頁第140頁
1999 Sep 28
138
Philips Semiconductors
Preliminary Device Specification
TV signal processor-Teletext decoder with
embedded
μ
-Controller
TDA935X/6X/8X series
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “IC package Databook” (order code 9398 652 90011).
SDIP
S
OLDERING BY DIPPING OR BY WAVE
The maximum permissible temperature of the solder is
260
°
C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
stg max
). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
R
EPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300
°
C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400
°
C, contact may be up to 5 seconds.
QFP
R
EFLOW SOLDERING
Reflow soldering techniques are suitable for all QFP
packages.
The choice of heating method may be influenced by larger
plastic QFP packages (44 leads, or more). If infrared or
vapour phase heating is used and the large packages are
not absolutely dry (less than 0.1% moisture content by
weight), vaporization of the small amount of moisture in
them can cause cracking of the plastic body. For details,
refer to the Drypack information in our “Quality Reference
Handbook” (order code 9397 750 00192).
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 50 and 300 seconds depending on heating
method. Typical reflow peak temperatures range from
215 to 250
°
C.
W
AVE SOLDERING
Wave soldering is
not
recommended for QFP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, for QFP
packages with a pitch (e) larger than 0.5 mm, the
following conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The footprint must be at an angle of 45
°
to the board
direction and must incorporate solder thieves
downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
R
EPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA936X | TV signal processor-Teletext decoder with embedded m-Controller |
| TDA938X | TV signal processor-Teletext decoder with embedded m-Controller |
| TDA9829T | Downconverter For DVB(下變頻器 （DVB應用）) |
| TDAT04622 | TDAT SONET/SDH 155/622/2488 Mbits/s Data Interfaces |
| TDAT042G51A-3BLL1 | TDAT SONET/SDH 155/622/2488 Mbits/s Data Interfaces |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA9380 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TDA938O超級芯片將微處理器(CPU)與TV信號處理器集成在一起 |
| TDA9383 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| TDA9400 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INTEGRATED CIRCUITS FOR TV AND RADIO RECEVERS |
| TDA9403 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INTEGRATED CIRCUITS FOR TV AND RADIO RECEVERS |
| TDA9500 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INTEGRATED CIRCUITS FOR TV AND RADIO RECEVERS |
發布緊急采購，3分鐘左右您將得到回復。