- 您現在的位置：買賣IC網 > PDF目錄98069 > S1C88409D 8-BIT, MROM, 8.8 MHz, MICROCONTROLLER, UUC108 PDF資料下載
參數資料
| 型號： | S1C88409D |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8.8 MHz, MICROCONTROLLER, UUC108 |
| 封裝： | DIE-108 |
| 文件頁數： | 80/250頁 |
| 文件大?。?/td> | 1877K |
| 代理商： | S1C88409D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁
160
EPSON
S1C88409 TECHNICAL MANUAL
CHAPTER 5: PERIPHERAL CIRCUITS AND OPERATION (Touch Panel Controller)
Starting coordinate detection
The touch panel controller starts coordinate
detection by writing "1" to the RST register.
When "1" is written to the RST register, the control-
ler first performs a pen-down check and is on
standby to touch panel driving and A/D conver-
sion for coordinate detection similar to the pen-
down check by writing "1" to the PDC register.
When a pen-down is detected, the controller starts
coordinate detection. At the same time, a pen-
down interrupt occurs if the interrupt is enabled.
However, the coordinate detection uses the clock
generated by the prescaler with the OSC3 clock as
the source clock. Therefore, it is necessary to turn
the OSC3 oscillation circuit on and to control the
prescaler so that the clock for the touch panel
controller is output before writing "1" to the RST
register.
Refer to Section 5.4 "Oscillation Circuit" and
Section 5.5 "Prescaler and Clock Control Circuit for
Peripheral Circuits" for controlling the clock.
The touch panel controller controls the signals as
follows and detects an X coordinate and a Y
coordinate separately.
X coordinate detection
BXL: HIGH (Negative electrode on X panel: ON)
BYH: HIGH (Positive electrode on Y panel: OFF)
BYL: LOW (Negative electrode on Y panel: OFF)
A/D channel:
Ch0
Y coordinate detection
BXH: HIGH (Positive electrode on X panel: OFF)
BXL: LOW (Negative electrode on X panel: OFF)
BYH: LOW (Positive electrode on Y panel: ON)
BYL: HIGH (Negative electrode on Y panel: ON)
A/D channel:
Ch1
Selected by mask option.
X panel
Y panel
A/D
conversion
A/D
conversion
Equivalent circuit
Fig. 5.17.3.1 Coordinate detection (X coordinate)
The touch panel is regarded as the equivalent
circuit shown in Figure 5.17.3.1. It outputs the
voltage to the A/D converter according to the
pointed coordinate.
The touch panel controller performs A/D conver-
sion at least 32 times (16 times each for X and Y
coordinates) per one coordinate and stores the
arithmetic mean to the coordinate data register as
the detection result.
Since the touch panel controller controls A/D
conversion during coordinate detection, do not
control the A/D converter with software.
While the RST register is set to "1", coordinate
detection is repeatedly performed as long as the
pen is touching the panel. It can be stopped by
writing "0" to the RST register. In this case, turn off
the clock output from the prescaler to the touch
panel controller and A/D converter.
Deciding pen-up status during coordinate
detection
In pen-down status (the pen is touching the panel),
the A/D conversion result indicates the coordi-
nates on the touch panel. If the result is smaller
than the value at the corner of the panel, it can be
regarded as pen-up status (the pen is not touching
the panel).
In this touch panel controller, a threshold value for
pen-up decision can be set according to the panel
to be used. When the mean value of the A/D
conversion result is smaller than the set value, the
touch panel controller decides it as pen-up status.
The threshold value for pen-up decision can be set
using the PUD register.
Table 5.17.3.1 Threshold value for pen-up decision
PUD3
0
1
PUD2
0
1
0
1
PUD1
0
1
0
1
0
1
0
1
PUD0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Pen-up decision
threshold value
4
8
12
16
20
24
28
32
36
40
44
48
52
56
60
64
The result of pen-up/down decision can be read
from the PEN bit (00FFA7HD0). The PEN bit goes
"0" in pen-up status and goes "1" in pen-down status.
During coordinate detection, a pen-up is judged
based on the determined data that is not regarded as
noise. If the input data is regarded as noise at pen-up,
it is not judged as pen-up and the PEN bit maintains
"1" (pen-down status).
相關PDF資料 |
PDF描述 |
|---|---|
| S1C88816D | 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC164 |
| S1C88832F0A0100 | MICROCONTROLLER, PQFP128 |
| S1C88848D0A0100 | 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC192 |
| S1C8F360F | 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP176 |
| S1D13305F00B | 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C88649 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88650 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88655 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88816 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88848 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。