- 您現在的位置：買賣IC網 > PDF目錄45387 > MQ83C154XXX-16/883D (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQFP44 PDF資料下載
參數資料
| 型號： | MQ83C154XXX-16/883D |
| 廠商： | TEMIC SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQFP44 |
| 文件頁數： | 171/204頁 |
| 文件大小： | 5687K |
| 代理商： | MQ83C154XXX-16/883D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁當前第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁
69
ATtiny40 [DATASHEET]
8263B–AVR–01/2013
In phase correct PWM mode the counter is incremented until the counter value matches TOP. When the counter
reaches TOP, it changes the count direction. The TCNT0 value will be equal to TOP for one timer clock cycle. The
timing diagram for the phase correct PWM mode is shown on Figure 11-7. The TCNT0 value is in the timing dia-
gram shown as a histogram for illustrating the dual-slope operation. The diagram includes non-inverted and
inverted PWM outputs. The small horizontal line marks on the TCNT0 slopes represent Compare Matches
between OCR0x and TCNT0.
The Timer/Counter Overflow Flag (TOV0) is set each time the counter reaches BOTTOM. The Interrupt Flag can
be used to generate an interrupt each time the counter reaches the BOTTOM value.
In phase correct PWM mode, the compare unit allows generation of PWM waveforms on the OC0x pins. Setting
the COM0x[1:0] bits to two will produce a non-inverted PWM. An inverted PWM output can be generated by setting
the COM0x[1:0] to three: Setting the COM0A0 bits to one allows the OC0A pin to toggle on Compare Matches if
the WGM02 bit is set. This option is not available for the OC0B pin (See Table 11-4 on page 72). The actual OC0x
value will only be visible on the port pin if the data direction for the port pin is set as output. The PWM waveform is
generated by clearing (or setting) the OC0x Register at the Compare Match between OCR0x and TCNT0 when the
counter increments, and setting (or clearing) the OC0x Register at Compare Match between OCR0x and TCNT0
when the counter decrements. The PWM frequency for the output when using phase correct PWM can be calcu-
lated by the following equation:
The N variable represents the prescale factor (1, 8, 64, 256, or 1024).
The extreme values for the OCR0x Register represent special cases when generating a PWM waveform output in
the phase correct PWM mode. If the OCR0x is set equal to BOTTOM, the output will be continuously low and if set
equal to TOP the output will be continuously high for non-inverted PWM mode. For inverted PWM the output will
have the opposite logic values.
At the very start of period 2 in Figure 11-7 on page 68 OCnx has a transition from high to low even though there is
no Compare Match. The point of this transition is to guarantee symmetry around BOTTOM. There are two cases
that give a transition without Compare Match.
OCR0x changes its value from TOP, like in Figure 11-7 on page 68. When the OCR0x value is TOPthe OCnx
pin value is the same as the result of a down-counting Compare Match. To ensure symmetry around BOTTOM
the OCnx value at TOP must correspond to the result of an up-counting Compare Match.
The timer starts counting from a value higher than the one in OCR0x, and for that reason misses the Compare
Match and hence the OCnx change that would have happened on the way up.
11.8
Timer/Counter Timing Diagrams
The Timer/Counter is a synchronous design and the timer clock (clk
T0) is therefore shown as a clock enable signal
in the following figures. The figures include information on when Interrupt Flags are set. Figure 11-8 on page 70
contains timing data for basic Timer/Counter operation. The figure shows the count sequence close to the MAX
value in all modes other than phase correct PWM mode.
fOCnxPCPWM
f
clk_I/O
2
N
TOP
--------------------------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| MR87C251SB16 | 8-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC44 |
| MC87C251SB16 | 8-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| MR87C51FC | 8-BIT, UVPROM, MICROCONTROLLER, CQCC44 |
| MD87C51FC-16 | 8-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| MT80C51T-36R | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MQ86 | 制造商:TE Connectivity 功能描述: |
| MQ8797BH | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intel 功能描述: |
| MQ87C196KC/R | 制造商:Rochester Electronics LLC 功能描述: |
| MQ87C196KD-16/B | 制造商:Rochester Electronics LLC 功能描述: |
| MQ87C196KD-20/R | 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。