- 您現在的位置：買賣IC網 > PDF目錄374311 > KBE00S009M (SAMSUNG SEMICONDUCTOR CO. LTD.) 1Gb NAND x 2 + 256Mb Mobile SDRAM x 2 PDF資料下載
參數資料
| 型號： | KBE00S009M |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 1Gb NAND x 2 + 256Mb Mobile SDRAM x 2 |
| 中文描述： | 1Gb的NAND × 2 256Mb的移動SDRAM × 2 |
| 文件頁數： | 32/86頁 |
| 文件大?。?/td> | 1898K |
| 代理商： | KBE00S009M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
MCP MEMORY
32
KBE00S009M-D411
Revision 1.0
May 2005
PAGE PROGRAM
The device is programmed basically on a page basis, but it does allow multiple partial page programing of a byte or consecutive bytes
up to 528 byte, in a single page program cycle. The number of consecutive partial page programming operation within the same page
without an intervening erase operation must not exceed 1 for main array and 2 for spare array. The addressing may be done in any
random order in a block. A page program cycle consists of a serial data loading period in which up to 528 bytes of data may be loaded
into the page register, followed by a non-volatile programming period where the loaded data is programmed into the appropriate cell.
Serial data loading can be started from 2nd half array by moving pointer. About the pointer operation, please refer to the attached
technical notes.
The serial data loading period begins by inputting the Serial Data Input command(80h), followed by the four cycle address input and
then serial data loading. The bytes other than those to be programmed do not need to be loaded.The Page Program confirm com-
mand(10h) initiates the programming process. Writing 10h alone without previously entering the serial data will not initiate the pro-
gramming process. The internal write state control automatically executes the algorithms and timings necessary for program and
verify, thereby freeing the system controller for other tasks. Once the program process starts, the Read Status Register command
may be entered, with RE and CE low, to read the status register. The system controller can detect the completion of a program cycle
by monitoring the R/B output, or the Status bit(I/O 6) of the Status Register. Only the Read Status command and Reset command are
valid while programming is in progress. When the Page Program is complete, the Write Status Bit(I/O 0) may be checked(Figure 9).
The internal write verify detects only errors for "1"s that are not successfully programmed to "0"s. The command register remains in
Read Status command mode until another valid command is written to the command register.
Figure 9. Program & Read Status Operation
80h
A
0
~ A
7
& A
9
~ A
27
528 Bytes Data
I/O
0
~
7
R/B
Address & Data Input
I/O
0
Pass
10h
70h
Fail
t
PROG
相關PDF資料 |
PDF描述 |
|---|---|
| KBE00S009M-D411 | 1Gb NAND x 2 + 256Mb Mobile SDRAM x 2 |
| KBJ2501 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2502 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2503 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2504 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KBE00S009M-D411 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:1Gb NAND x 2 + 256Mb Mobile SDRAM x 2 |
| KB-E100SRW | 功能描述:LED 顯示器和配件 Red 640nm 90mcd Diffused Light Bar RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| KB-E100SURKW | 功能描述:LED條和陣列 8.89X3.81MM RED LT BAR LED DISPLAY RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube |
| KBE1A11N | 制造商:Lovato Electric Inc 功能描述: |
| KBEV 5T-0.5-RSSV 4.5T | 制造商:TURCK Inc 功能描述:KBEV 5T-0.5-RSSV 4.5T |
發布緊急采購，3分鐘左右您將得到回復。