- 您現在的位置：買賣IC網 > PDF目錄383134 > ISL5416EVAL1 (Intersil Corporation) Four-Channel Wideband Programmable DownConverter PDF資料下載
參數資料
| 型號： | ISL5416EVAL1 |
| 廠商： | Intersil Corporation |
| 英文描述： | Four-Channel Wideband Programmable DownConverter |
| 中文描述： | 四通道可編程寬帶下變頻器 |
| 文件頁數： | 24/71頁 |
| 文件大?。?/td> | 1128K |
| 代理商： | ISL5416EVAL1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
24
Serial Data Output
The serial data output control register contains sync position
and polarity (SSYNCA, B, C or D), channel multiplexing, and
scaling controls for the SD1x and SD2x (x = A, B, C or D)
serial outputs (see IWA registers 0*06 - 0*08h).
Serial Data Output Time Slot
Content/Format Registers
These two registers are used to program the content and
format of the serial data output sequence time slots (see
IWA registers 0*07h and 0*08h). There are four data time
slots that make up a serial data output stream. The number
of data bits and data format of each slot is programmable as
well as whether there will be a sync generated with the time
slot (the syncs are only associated with the SD1 serial
outputs). Any of three types of data or zeros can be chosen
for each time slot. Seven bits are used to specify the content
and format of each slot.
Channel Routing Mask
The multiplexing mask bits for each channel (see
Microprocessor Interface Section, IWA register 0*06h bits
19:16 for SD1x or bits 15:12 for SD2x) can be used to enable
that channel’s output to any of the four serial outputs. These
bits control AND gates that mask off the channels, so a zero
disables the channel’s connection to that output.
To configure more than one channel's output onto a serial
data output, the SD1 serial outputs and syncs from each
channel (0,1, 2 and 3) are brought to each of the SD1 serial
output sections and the SD2 serial outputs are brought to
each of the SD2 serial output sections (the syncs are only
associated with the SD1 serial outputs). There, the four
outputs are AND-ed with the multiplexing mask programmed
in the serial data output control registers of channels 0 thru 3
and OR-ed together. By gating off the channels that are not
wanted and delaying the data from each desired channel
appropriately, the channels can be multiplexed into a
common serial output stream. It should be noted that in
order to multiplex multiple channels onto a single serial data
stream the channels to be multiplexed must be synchronous.
Microprocessor Interface
The ISL5416 Microprocessor (
μ
P) interface consists of a 16-
bit bidirectional data bus, P(15:0), three address pins,
ADD(2:0), a write strobe (WR), a read strobe (RD) and a
chip enable (CE). Indirect addressing is used for control and
configuration of the ISL5416.
The processor interface to the ISL5416 is a mixture of direct
and indirect addressing. To minimize the amount of
processor address space and bus routing, there are only
eight 16-bit direct address locations. Two of these are used
to access an internal 32-bit bus. To write data to internal
indirect locations, the data is first written to direct addresses
0 (bits 15:0) and 1 (bits 31:16). The internal address is then
written to direct address 2. When the address is written, a
synchronization circuit generates an internal write strobe,
synchronized to the clock, to clock the data into the target
register. The synchronization process requires 4 clock
cycles, so data should not be written to direct addresses 0 or
1 for four clock cycles after a write to address 2. To read data
from internal locations, the internal address is first written to
direct address 3. The data can then be read from direct
addresses 0 (15:0) and 1 (31:16). The indirect address
register is shared between direct addresses 2 and 3, with
only writes to address 2 generating write strobes. Because
of this, the address does not have to be re-written to verify a
write unless broadcasting data to more than one channel.
Direct address 2 is used for status when read. The status
bits are defined in Table of Microprocessor Direct
Read/Write Addresses. Direct addresses 4 through 7 are
used for fast read access.
Addresses 4 through 7 (one address per channel) are used
for sequenced read (FIFO-like) addresses. The user can
program the order that the data would be read from the part.
The user can select I, Q, AGC Gain (real time or sampled),
and two types of data from the range control circuit. When a
new output is available, the data type pointer is reset to the
first data type. After each read, the pointer is incremented to
the next data type. To signal a new output on the channel, a
signal can be routed to the CLKO2/INTRPT pin. A channel is
enabled to generate interrupt in address IWA = 0*0Ah, bit 31.
If separate interrupt signals are required for each channel,
the FSYNCX pins can be used.
The indirect address space is divided into top level or global
locations for parameters that are shared between channels
or I/Os, I/O control locations, and channel control
parameters. The global locations are between addresses
0000h and 00FFh. The I/O control locations are between
0100h and 0FFFh. Bits 11, 10, 9, and 8 select I/O busses D,
C, B, and A, respectively. What this means is that by setting
a single address bit of 11:8, the control register is written for
that I/O control section. By setting more than one bit, the
same data is written to the corresponding registers of more
than one I/O control section. Reads must select only one I/O
control section.
Channel control registers are located between addresses
1000h and FFFFh. Bits 15, 14, 13, and 12 select channels 3,
2, 1, and 0, respectively. The user can write to individual
channels or to multiple channels at once by setting the
appropriate channel select bit, 15:12. Read addresses must
specify a single channel.
ISL5416
相關PDF資料 |
PDF描述 |
|---|---|
| ISL5416KIZ | Four-Channel Wideband Programmable DownConverter |
| ISL54200_07 | USB 2.0 High/Full Speed Multiplexer |
| ISL54200IRUZ-T | USB 2.0 High/Full Speed Multiplexer |
| ISL54200 | USB 2.0 High/Full Speed Multiplexer |
| ISL54200IRZ | USB 2.0 High/Full Speed Multiplexer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL5416KI | 功能描述:上下轉換器 QUAD WIDEBAND DOWN CONVERTER, 256 CABGA RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| ISL5416KIZ | 制造商:Intersil Corporation 功能描述:LEAD-FREE QUAD WIDEBAND DOWN CONVERTER, 256 CABGA - Trays 制造商:Intersil Corporation 功能描述:PB-FREE W/ANNEAL QUAD DIGITAL DOWNCONVER 制造商:Intersil 功能描述:QD WIDEB& DWN CNVRTR 256 CABGA |
| ISL54200 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:USB 2.0 High/Full Speed Multiplexer |
| ISL54200_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:USB 2.0 High/Full Speed Multiplexer |
| ISL54200EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL54200 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。