- 您現在的位置：買賣IC網 > PDF目錄360789 > ICSXXXXY Auto-Negotiation Advertisement Register (register 4 [0x04]) PDF資料下載
參數資料
| 型號： | ICSXXXXY |
| 英文描述： | Auto-Negotiation Advertisement Register (register 4 [0x04]) |
| 中文描述： | 自動談判廣告登記（注冊4 [0x04]） |
| 文件頁數： | 43/66頁 |
| 文件大小： | 1725K |
| 代理商： | ICSXXXXY |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
43
ICS1890
MII Management Interface
Management Data Clock
The Management Data Clock (MDC) is used by the
ICS1890
to synchronize the transfer of management information to or
from the
ICS1890
using the serial MDIO data line.
MDC
Management Data Input/Output
The Management Data Input/Output (MDIO) is a tri-statable
line driven by station management to transfer command
information or driven by the
ICS1890
to transfer status
information. All transfers and sampling are synchronous with
MDC. If the
ICS1890
is to be used in an application which
uses the mechanical MII specification, MDIO must have a
1.5K
±5% pull-up at the
ICS1890
end and a 2K
±5% pull-
down at the station management end. This enables station
management to deter-mine if the connection is intact.
MDIO
Twisted Pair Interface
Transmit Pair
The Transmit pair TP_TX+ and TP_TX- carries the serial bit
stream for transmission over the UTP cable. The current-
driven differential driver is programmed to produce two-level
(10Base-T, Manchester) or three-level (100Base-TX, MLT-3)
signals depending on the mode of operation selected (manually
or by Auto-Negotiation). These output signals interface directly
with an isolation transformer.
TP_TX+ & TP_TX-
Note that these pins may be tristated using the TPTRI control
pin.
Receive Pair
The Receive pair TP_RX+ and TP_RX- carries the serial bit
stream from the mandatory isolation transformer. The serial bit
stream may be two-level (10Base-T, Manchester) or three-
level (100Base-TX, MLT-3) signals depending on the ICS
mode of operation
TP_RX+ & TP_RX-
10M Transmit Current Set Resistor
A resistor is required to be connected between this pin and
the nearest transmit ground to set the value of the transmit
current used in 10M mode.
10TCSR
The value and tolerance of this resistor is specified in the
Electricals section.
100M Transmit Current Set Resistor
A resistor is required to be connected between this pin and
the nearest transmit ground to set the value of the transmit
current used in 100M mode.
100TCSR
The value and tolerance of this resistor is specified in the
Electricals section.
Clock Reference Interface
Frequency Reference
These pins connect to the 25 MHz crystal or the frequency
reference source.
(REF_IN & REF_OUT)
When a frequency reference source like a crystal oscillator
module is used, its output should be connected to REF_IN
and REF_OUT should be left unconnected.
Configuration and Status Interface
Node/Repeater Mode
When this input is logic zero, the device will default to Node
operation. SQE test will default to on for 10Base-T.
NOD/REP
When this input is logic one, the device will default to Repeater
operation. SQE test will default to off and Carrier Sense will be
determined by receive activity only.
This pin setting also affects which clock, TXCLK or REF_IN,
is used to latch the transmit data, TXD. See the description of
the ITCLS pin for the details.
MII Data/Stream Interface Select
This input pin selects the MAC to PHY interface to be used.
When the input is low the MII Data Interface is selected.
MII/SI
When this input is high, the Stream Interface is selected.
The Stream Interface that is used depends on the settings
of the 10/100SEL and 10/LP pins which allow selection of the
100M Stream Interface, 10M/Serial Interface, or Link Pulse
Interface.
10M Serial/Link Pulse Interface Select
This input selects between the 10M Serial and Link Pulse
Interfaces when Stream Interface mode is selected with the
MII/SI pin. When this input is low and Stream Interface mode
is selected, the 10M Serial Interface is selected. When this
input is high and Stream Interface mode is selected, the Link
Pulse Interface is selected.
10/LP
相關PDF資料 |
PDF描述 |
|---|---|
| ICX055ALA | AREA CCD IMAGE ARRAY |
| ICX055BLA | Optoelectronic |
| ICX056AK | AREA CCD IMAGE ARRAY |
| ICX056AKB | AREA CCD IMAGE ARRAY |
| ICX057AK | AREA CCD IMAGE ARRAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICSXXXXYFLFT | 制造商:ICS 制造商全稱:ICS 功能描述:System Clock Chip for ATI RS400 P4TM-based Systems |
| ICSXXXXYGLFT | 制造商:ICS 制造商全稱:ICS 功能描述:System Clock Chip for ATI RS400 P4TM-based Systems |
| IC-SY WK1D | 制造商:LASER COMPONENTS 功能描述:DEVELOPMENT KIT LD DRIVER |
| ICT-075-A-10.0-G | 制造商:Interconnect Devices Inc (IDI) 功能描述:contact probe, .075' CTR 3 amp, concave 90 deg |
| ICT-075-A-10-G S/C | 功能描述:觸點探頭 .075’ CTR 3AMP PROBE HEADED 90 DEG CNCAVE RoHS:否 制造商:IDI 類型:Probes 尖端類型:Spherical Radius 長度:8.26 mm 電流額定值:10 A 彈力:2.3 oz 行程:1.52 mm 系列:101050 |
發布緊急采購，3分鐘左右您將得到回復。