參數資料
型號： ICSXXXXY
英文描述： Auto-Negotiation Advertisement Register (register 4 [0x04])
中文描述： 自動談判廣告登記（注冊4 [0x04]）
文件頁數： 3/66頁
文件大?。?/td> 1725K
代理商： ICSXXXXY
3
ICS1890
Modes of Operation
Reset & Basic Initialization
Reset can be accomplished using either register bit 0:15 or the
RESET pin.
For a hardware reset, RESET must be held at a logic zero level
for at least two clock cycles and may be held low as long as
desired.
While RESET is held low the device is in Low Power mode.
After the RESET pin is released to a logic one level, Low
Power mode is exited, the PHY address is latched into register
16, and the reset process continues to completion.
For a software reset, a management agent must write a logic
one to register bit 0:15. This will start the reset process. The
software reset bit will clear itself automatically when reset is
completed.
All reset timing parameters are specified in the Electricals
section of the data sheet.
Low Power and Automatic 100Base-T Power-
Down
The
ICS1890
supports two power saving modes. The
ICS1890
device can be placed into a state where very littler power is
drawn by the device. This Low Power mode can be activated
by holding the RESET pin continuously low or by writing a
logic one to the Power-down bit (0:11).
When the device is in Low Power mode, all functions are
disabled except for register access through the MII Management
Interface.
All register values are maintained during Low Power mode,
except for latching status bits, which are reset to their default
values.
The
ICS1890
can also automatically reduce its total power
requirements when operating in 10Base-T mode by automatically
powering-down the 100Base-TX modules.
The power required by the
ICS1890
in normal, 100Base-TX
power-down, and Low Power modes is given in the Electricals
section of the data sheet.
Auto-Negotiation
A link can automatically be established using Auto-Negotiation.
When enabled, Auto-Negotiation will exchange information
about the local nodes capabilities with its remote link partner.
After the information is exchanged, each device compares its
capabilities with those of its partner and then the highest
performance operational mode is automatically selected.
As an example, if one device supports 10Base-T and 100Base-
TX, and the other device supports 100Base-TX and 100Base-
T4, 100Base-TX will automatically be selected.
See the Auto-Negotiation section for more details on how the
process is initiated and controlled.
100Base-TX
The primary operational mode of the
ICS1890
is to provide
100Base-TX physical layer services. This consists mainly of
converting data from parallel to serial at a 100 Mb/s data rate.
The device may be configured in a number of different ways
and also provides detailed operational status information.
10Base-T
The
ICS1890
also provides 10Base-T physical layer services
to allow easy migration from 10 to 100 Mb/s service. Complete
data service is provided with configuration and status available
to management.
Full Duplex
The
ICS1890
supports either half and full duplex operation
for both 10Base-T and 100Base-TX. Full Duplex operation
allows simultaneous transmission and reception of data which
can effectively double data throughput to 20 or 200 Mb/s.
To operate in Full Duplex mode, some of the standard 10Base-
T and 100Base-TX behaviors are modified.
In 10Base-T Full Duplex mode, transmitted data is not looped
back to the receiver and SQE test is not performed.
In both 10Base-T and 100Base-TX Full Duplex modes, CRS is
asserted in response only to receive activity and COL always
remains inactive.
相關PDF資料
PDF描述
ICX055ALA AREA CCD IMAGE ARRAY
ICX055BLA Optoelectronic
ICX056AK AREA CCD IMAGE ARRAY
ICX056AKB AREA CCD IMAGE ARRAY
ICX057AK AREA CCD IMAGE ARRAY
相關代理商/技術參數
參數描述
ICSXXXXYFLFT 制造商:ICS 制造商全稱:ICS 功能描述:System Clock Chip for ATI RS400 P4TM-based Systems
ICSXXXXYGLFT 制造商:ICS 制造商全稱:ICS 功能描述:System Clock Chip for ATI RS400 P4TM-based Systems
IC-SY WK1D 制造商:LASER COMPONENTS 功能描述:DEVELOPMENT KIT LD DRIVER
ICT-075-A-10.0-G 制造商:Interconnect Devices Inc (IDI) 功能描述:contact probe, .075' CTR 3 amp, concave 90 deg
ICT-075-A-10-G S/C 功能描述:觸點探頭 .075’ CTR 3AMP PROBE HEADED 90 DEG CNCAVE RoHS:否 制造商:IDI 類型:Probes 尖端類型:Spherical Radius 長度:8.26 mm 電流額定值:10 A 彈力:2.3 oz 行程:1.52 mm 系列:101050
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*