- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9090 (Gennum Corporation) GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9090 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| 中文描述： | GS9090 GenLINX - R的第三270Mb / s的SDI和DVB解串器，意大利航天局 |
| 文件頁數： | 24/70頁 |
| 文件大?。?/td> | 696K |
| 代理商： | GS9090 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
GS9090 Data Sheet
28201 - 1
July 2005
24 of 70
NOTE: The PCLK output will continue to operate at 27MHz +/- 7.5% during the lock
detection process. Only when the device is locked (LOCKED = HIGH) will the
PCLK output an accurate 27MHz signal.
For SMPTE and DVB-ASI inputs, the lock detect block will only assert the LOCKED
output pin HIGH if (1) the reclocker has locked to the input data stream, and (2)
TRS or DVB-ASI sync words have been correctly identified.
For serial inputs that do not conform to SMPTE or DVB-ASI formats, one of the
following will occur once the reclocker has locked:
1. In Manual mode, data will be passed directly to the parallel outputs without any
further processing taking place and the LOCKED signal will be asserted HIGH
if and only if the SMPTE_BYPASS and DVB_ASI input pins are set LOW (see
Data-Through functionality on page 29
); or
2. In Auto mode, the LOCKED signal will be asserted LOW, the parallel outputs
will be set to logic LOW, and the SMPTE_BYPASS and DVB_ASI output
signals will also be set LOW.
If the internal reclocker does not lock to the input, the internal pll_lock signal will be
LOW, and the lock detect block will not search for sync words. The LOCKED signal
will be set LOW, and all device outputs except PCLK will be forced LOW. The
PCLK output frequency will be 27MHz +/- 7.5% over the temperature range of
-20
o
C to +85
o
C.
3.5.2 Auto Mode
Recall that the GS9090 is in Auto mode when the AUTO/MAN input pin is set HIGH
by the application layer. In this mode, SMPTE_BYPASS and DVB_ASI become
output status pins.
Table 3-1
shows the status of these pins when different serial
digital video signals are applied.
Table 3-1: Auto Mode Output Status Signals
Pin Settings
Format
SMPTE_BYPASS
DVB_ASI
SD SMPTE
HIGH
LOW
DVB-ASI
LOW
HIGH
NOT SMPTE OR DVB-ASI*
LOW
LOW
*NOTE: In this case the device will not be locked (LOCKED = LOW), and all digital output pins
except PCLK will be set LOW (see
Lock Detect on page 22
)
相關PDF資料 |
PDF描述 |
|---|---|
| GS9090-CNE3 | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| GS9092A | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9090A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9090A GenLINX-R III 270Mb/s Deserializer for SDI |
| GS9090A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer |
| GS9090ACNE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer 56-Pin QFN EP 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer for SDI & ASI |
| GS9090B | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
| GS9090B_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
發布緊急采購，3分鐘左右您將得到回復。