- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9090 (Gennum Corporation) GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9090 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| 中文描述： | GS9090 GenLINX - R的第三270Mb / s的SDI和DVB解串器，意大利航天局 |
| 文件頁數： | 31/70頁 |
| 文件大?。?/td> | 696K |
| 代理商： | GS9090 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
GS9090 Data Sheet
28201 - 1
July 2005
31 of 70
The FIFO_LD_POSITION[12:0] register is designed to accommodate the longest
SD line length. If the user programs a value greater than the maximum line length
at the operating SD standard, the FIFO_LD pulse will not be generated.
After a device reset, the FIFO_LD_POSITION[12:0] register is set to zero and the
FIFO_LD pulse will assume the default timing.
3.9.2 Ancillary Data Detection and Indication
The GS9090 will detect all types of ancillary data in either the vertical or horizontal
data spaces. The ANC_DETECT status signal is provided to indicate the position
of ancillary data in the output data stream. This signal is available for output on the
multi-function output port pins, if so programmed (see
Programmable
Multi-Function Outputs on page 56
).
The ANC_DETECT status signal is synchronous with PCLK and can be used as a
clock enable to external logic, or as a write enable to an external FIFO or other
memory device. The ANC_DETECT signal will be asserted HIGH whenever
ancillary data is detected in the video data stream (see
Figure 3-5
). Both 8-bit and
10-bit ancillary data preambles will be detected by the GS9090.
NOTE 1: When the internal FIFO is configured for video mode, the ANC_DETECT
signal will be timed to the data output from the FIFO (see
Video Mode on page 46
).
NOTE 2: For performance in low latency mode, see GS9090 Low-latency Mode on
page 58.
Figure 3-5: ANC_DETECT Status Signal
3.9.2.1 Programmable Ancillary Data Detection
Although the GS9090 will detect all types of ancillary data by default, it also allows
the application layer to specifically program up to five different ancillary data types
for detection. This is accomplished by setting the ANC_TYPE registers via the host
interface (see
Table 3-4
).
For each data type to be detected, the host interface must program the DID and/or
SDID of the ancillary data type of interest. The GS9090 will compare the received
DID and/or SDID with the programmed values and assert ANC only if an exact
match is found. The same timing shown in
Figure 3-5
will be used.
3FF
000
3FF
DID
DBN
DC
ANC DATA
ANC DATA
CSUM
BLANK
ANC_DETECT
Y'CbCr DATA
PCLK
相關PDF資料 |
PDF描述 |
|---|---|
| GS9090-CNE3 | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| GS9092A | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9090A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9090A GenLINX-R III 270Mb/s Deserializer for SDI |
| GS9090A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer |
| GS9090ACNE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer 56-Pin QFN EP 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer for SDI & ASI |
| GS9090B | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
| GS9090B_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
發布緊急采購，3分鐘左右您將得到回復。