- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9090 (Gennum Corporation) GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9090 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| 中文描述： | GS9090 GenLINX - R的第三270Mb / s的SDI和DVB解串器，意大利航天局 |
| 文件頁數： | 39/70頁 |
| 文件大?。?/td> | 696K |
| 代理商： | GS9090 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
GS9090 Data Sheet
28201 - 1
July 2005
39 of 70
All bits, with the exception of the LOCK_ERR, will also be cleared if a change in the
video standard is detected, or under the following conditions:
The whole ERROR_STATUS register, including the LOCK_ERR bit, will be set
LOW during a system reset (RESET = LOW).
LOCKED is asserted LOW
SMPTE_BYPASS is asserted LOW in Manual mode
In addition to the ERROR_STATUS register, a register called ERROR_MASK is
included to select the specific error conditions that will be detected (
Table 3-12
).
There is one bit in the ERROR_MASK register for each type of error represented
in the ERROR_STATUS register.
The bits of the ERROR_MASK register will default to '0' after a device reset, thus
allowing all error types to be detected. The host interface may disable individual
error detection by setting the corresponding bit HIGH in this register.
Error conditions are also indicated to the application layer via the status signal pin
DATA_ERROR. This output pin is an inverted logical 'OR'ing of each error status
flag stored in the ERROR_STATUS register. DATA_ERROR is normally HIGH, but
will be set LOW by the device when an error condition that has not been masked
is detected.
Table 3-11: Host Interface Description for Error Status Register
Register Name
Bit
Name
Description
R/W
Default
ERROR_STATUS
Address: 01h
15-7
–
Not Used
–
–
6
VD_STD_ERR
Video Standard Error Flag. Set HIGH when a
mismatch between the received SMPTE 352M
packets (version 1 or version 0) and the
calculated video standard occurs.
R
0
5
FF_CRC_ERR
Full Field CRC Error Flag. Set HIGH when a Full
Field (FF) CRC mismatch has been detected in
Field 1 or 2
R
0
4
AP_CRC_ERR
Active Picture CRC Error Flag. Set HIGH when an
Active Picture (AP) CRC mismatch has been
detected in Field 1 or 2.
R
0
3
LOCK_ERR
Lock Error Flag. Set HIGH whenever the
LOCKED pin is LOW (indicating the device is not
correctly locked).
R
0
2
CS_ERR
Checksum Error Flag. Set HIGH when ancillary
data packet checksum error has been detected.
R
0
1
SAV_ERR
Start of Active Video Error Flag. Set HIGH when
TRS errors are detected in either 8-bit or 10-bit
TRS words.
R
0
0
EAV_ERR
End of Active Video Error Flag. Set HIGH when
TRS errors are detected in either 8-bit or 10-bit
TRS words.
R
0
相關PDF資料 |
PDF描述 |
|---|---|
| GS9090-CNE3 | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| GS9092A | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9090A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9090A GenLINX-R III 270Mb/s Deserializer for SDI |
| GS9090A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer |
| GS9090ACNE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer 56-Pin QFN EP 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer for SDI & ASI |
| GS9090B | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
| GS9090B_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
發布緊急采購，3分鐘左右您將得到回復。