- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9090 (Gennum Corporation) GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9090 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| 中文描述： | GS9090 GenLINX - R的第三270Mb / s的SDI和DVB解串器，意大利航天局 |
| 文件頁數： | 28/70頁 |
| 文件大小： | 696K |
| 代理商： | GS9090 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
GS9090 Data Sheet
28201 - 1
July 2005
28 of 70
3.6.4 HVF Timing Signal Generation
The GS9090 extracts critical timing parameters from either the received TRS
signals (FW_EN = LOW) or from the internal flywheel-timing generator (FW_EN =
HIGH).
Horizontal blanking period (H), vertical blanking period (V), and field odd / even
timing (F) are extracted and are available for output on any of the multi-function
output port pins, if so programmed (see
Programmable Multi-Function Outputs on
page 56
).
The H signal timing is configurable via the H_CONFIG bit of the internal
IOPROC_DISABLE register as either active line-based blanking, or TRS-based
blanking (see
Table 3-14
in
Error Correction and Insertion on page 43
).
The default setting of this bit (after RESET has been asserted) is LOW.
Active line-based blanking is enabled when the H_CONFIG bit is set LOW. In this
mode, the H output is HIGH for the entire horizontal blanking period, including the
EAV and SAV TRS words. This is the default H timing used by the device.
When H_CONFIG is set HIGH, TRS based blanking is enabled. In this case, the H
output will be HIGH for the entire horizontal blanking period as indicated by the H
bit in the received TRS ID words.
The timing of these signals is shown in
Figure 3-3
.
NOTE 1: When the internal FIFO is configured for video mode, the H, V, and F
signals will be timed to the data output from the FIFO (see
Video Mode on
page 46
).
NOTE 2: When the GS9090 is configured for Low-latency mode, the H, V, and F
output timing will be TRS-based only as shown in
GS9090 Low-latency Mode on
page 58
. Active line-based timing is not available in this mode, and the setting of
the H_CONFIG host interface bit will be ignored.
Figure 3-3: H,V,F Timing
Y/Cr/Cb DATA OUT
PCLK
H
V
F
XYZ
000
000
3FF
XYZ
000
000
3FF
H SIGNAL TIMING:
H_CONFIG = LOW (Default)
H_CONFIG = HIGH
相關PDF資料 |
PDF描述 |
|---|---|
| GS9090-CNE3 | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| GS9092A | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9090A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9090A GenLINX-R III 270Mb/s Deserializer for SDI |
| GS9090A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer |
| GS9090ACNE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer 56-Pin QFN EP 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer for SDI & ASI |
| GS9090B | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
| GS9090B_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
發布緊急采購，3分鐘左右您將得到回復。