- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9090 (Gennum Corporation) GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI PDF資料下載
參數資料
| 型號： | GS9090 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| 中文描述： | GS9090 GenLINX - R的第三270Mb / s的SDI和DVB解串器，意大利航天局 |
| 文件頁數： | 25/70頁 |
| 文件大?。?/td> | 696K |
| 代理商： | GS9090 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
GS9090 Data Sheet
28201 - 1
July 2005
25 of 70
3.5.3 Manual Mode
Recall that the GS9090 is in Manual mode when the AUTO/MAN input pin is set
LOW by the application layer. In this mode the SMPTE_BYPASS and DVB_ASI
pins become input signals, and the application layer determines the operating
mode of the device by setting these pins as shown in
Table 3-2
.
3.6 SMPTE Functionality
The GS9090 enters SMPTE mode once the device has detected SMPTE TRS sync
words and locked to the input data stream as described in
Lock Detect on page 22
.
The GS9090 will remain in SMPTE mode until such time that SMPTE TRS sync
words fail to be detected.
The lock detect block may also drop out of SMPTE mode under any of the following
conditions:
TRS word detection is a continuous process, and the device will identify both 8-bit
and 10-bit TRS words.
SMPTE_BYPASS is asserted LOW in Manual mode
RESET is asserted LOW
LOCKED is LOW (i.e. the device loses lock to the input signal)
In Auto mode, the GS9090 sets the SMPTE_BYPASS pin HIGH and the DVB_ASI
pin LOW to indicate that it has locked to a SMPTE input data stream. When
operating in Manual mode, the application layer must assert the DVB_ASI pin LOW
and the SMPTE_BYPASS pin HIGH in order to enable SMPTE operation.
Table 3-2: Manual Mode Input Status Signals
Pin Settings
Format
SMPTE_BYPASS
DVB_ASI
SD SMPTE
HIGH
LOW
DVB-ASI
X
HIGH
NOT SMPTE OR DVB-ASI
(Data-Through mode)*
LOW
LOW
*NOTE: See
Data-Through functionality on page 29
for more detail on Data-Through mode
相關PDF資料 |
PDF描述 |
|---|---|
| GS9090-CNE3 | GS9090 GenLINX-R III 270Mb/s Deserializer for SDI and DVB-ASI |
| GS9092A | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092ACNE3 | GS9092A GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
| GS9092-CNE3 | GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9090A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9090A GenLINX-R III 270Mb/s Deserializer for SDI |
| GS9090A_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer |
| GS9090ACNE3 | 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer 56-Pin QFN EP 制造商:Semtech Corporation 功能描述:270Mb/s Deserializer for SDI & ASI |
| GS9090B | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
| GS9090B_10 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GenLINX III 270Mb/s Deserializer for SDI |
發布緊急采購，3分鐘左右您將得到回復。