- 您現在的位置：買賣IC網 > PDF目錄367000 > CYP15G0101DXA-BBC Telecomm/Datacomm PDF資料下載
參數資料
| 型號： | CYP15G0101DXA-BBC |
| 元件分類： | 通信、網絡模塊及開發工具 |
| 英文描述： | Telecomm/Datacomm |
| 中文描述： | 電信/數據通信 |
| 文件頁數： | 31/78頁 |
| 文件大小： | 1555K |
| 代理商： | CYP15G0101DXA-BBC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
CYP15G04K100V1-MGC
CYP15G04K200V2-MGC
PRELIMINARY
Document #: 38-02044 Rev **
Page 31 of 78
nal EEPROM. Configuration, on the other hand, is defined as
the loading of a user
’
s design into the volatile CPLD block.
Configuration can begin in two ways. It can be initiated by tog-
gling the
Reconfig
pin from LOW to HIGH, or by issuing the
appropriate IEEE std 1149.1 JTAG instruction to the PSI de-
vice via the JTAG interface. There are two IEEE std 1149.1
JTAG instructions that initiate configuration of the PSI. The
Self
Config
instruction causes the PSI to (re)configure with data
store in the internal EEPROM. The
Load Config
instruction
causes the PSI to (re)configure with data provided by other
sources such as a PC, automatic test equipment (ATE), or an
embedded microcontroller/processor via the JTAG port.
There are multiple configuration options available for issuing
the IEEE std 1149.1 JTAG instructions to the PSI. The first
method is to use a PC with the C3 ISR programming cable and
software. With this method, the ISR pins of the PSI devices in
the system are routed to a connector at the edge of the printed
circuit board. The C3 ISR programming cable is then connect-
ed between the PC and this connector. A simple configuration
file instructs the ISR software of the programming operations
to be performed on the PSI devices in the system. The ISR
software then automatically completes all of the necessary
data manipulations required to accomplish configuration,
reading, verifying, and other ISR functions. For more informa-
tion on the Cypress ISR interface, see the Programming/ISR
application notes at http://www.cypress.com/pld/pldapp-
notes.html.
For systems with embedded controllers/processors, a control-
ler/processor may be used to configure the PSI. The PSI ISR
software assists in this method by converting the device HEX
file into the ISR serial stream that contains the ISR instruction
information and the addresses and data of locations to be con-
figured. The controller/processor then simply directs this ISR
stream to the chain of PSI devices to complete the desired
reconfiguration or diagnostic operations. Contact your local
sales office for information on availability of this option.
Programming
The on-chip EEPROM device of the CPLD block is pro-
grammed by issuing the appropriate IEEE std 1149.1 JTAG
instruction. This can be done automatically using ISR/STAPL
software. The configuration bits are sent from a PC through the
JTAG port into the PSI via the C3 ISR programming cable. The
data is then passed to the internal EEPROM through the Non-
Volatile (NV) port of the CPLD block. For more information on
how to program the PSI through ISR/STAPL, please refer to
the ISR/STAPL User Guide.
Third-Party Programmers
Cypress support is available on a wide variety of third-party
programmers. All major programmers (including BP Micro,
System General, Hi-Lo) support the PSI family.
Development Software Support
Warp
Warp
is a state-of-the-art design environment for designing
with Cypress programmable logic.
Warp
utilizes a subset of
IEEE 1076/1164 VHDL and IEEE 1364 as the Hardware De-
scription Language (HDL) for design entry.
Warp
accepts
VHDL or Verilog input, synthesizes and optimizes the entered
design, and outputs a configuration bitstream for the desired
Delta39K device. For simulation,
Warp
provides a graphical
waveform simulator as well as VHDL and Verilog Timing Mod-
els.
VHDL and Verilog are open, powerful, non-proprietary Hard-
ware Description Languages (HDLs) that are standards for be-
havioral design entry and simulation. HDL allows designers to
learn a single language that is useful for all facets of the design
process.
Third-Party Software
Cypress products are supported in a number of third-party de-
sign entry and simulation tools. Refer to the third-party soft-
ware data sheet or contact your local sales office for a list of
currently supported third party vendors.
Figure 15. JTAG Interface
Instruction Register
Boundary Scan
idcode
Usercode
ISR Prog.
Bypass Reg.
Data Registers
JTAG
TAP
CONTROLLER
TDO
TDI
TMS
TCLK
相關PDF資料 |
PDF描述 |
|---|---|
| CYP15G0403DXB | Physical Layer Devices |
| CYP15G0101 | Single-channel HOTLink Transceiver |
| CYP15G0101DXB | Single-channel HOTLink Transceiver |
| CYP15G0101DXB-BBC | Single-channel HOTLink Transceiver |
| CYP15G0101DXB-BBI | Single-channel HOTLink Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYP15G0101DXA-BBI | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Single Channel HOTLink II Transceiver |
| CYP15G0101DXB | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Single-channel HOTLink II⑩ Transceiver |
| CYP15G0101DXB_11 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Single-channel HOTLink II Transceiver Compliant to multiple standards |
| CYP15G0101DXB_12 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Single-channel HOTLink IIa?￠ Transceiver |
| CYP15G0101DXB-BBC | 功能描述:電信線路管理 IC Single Channel XCVR 1.5Gbps Bckplane COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。