參數資料
型號： CYP15G0101DXA-BBC
元件分類： 通信、網絡模塊及開發工具
英文描述： Telecomm/Datacomm
中文描述： 電信/數據通信
文件頁數： 28/78頁
文件大?。?/td> 1555K
代理商： CYP15G0101DXA-BBC
CYP15G04K100V1-MGC
CYP15G04K200V2-MGC
PRELIMINARY
Document #: 38-02044 Rev **
Page 28 of 78
Table 26. Receive Character Status Bits
Within these status decodes, there are three forms of status
reporting. The two normal or data status reporting modes
(Type A and Type B) are selectable through the RXMODE[0]
input. These status types allow compability with legacy
systems, while allowing full reporting in new systems. The third
status type is used for reporting receive BIST status and
progress. These status values are generated in part by the
Receive Synchronization State Machine, and are listed in
Table 26
.
Receive Synchronization State Machine
Each receive channel contains a Receive Synchronization
state machine. This machine handles loss and recovery of bit,
channel, and word framing, and part of the control for channel
bonding. This state machine is enabled whenever the receive
channels are configured for channel bonding (RXMODE[1]
≠
LOW). Separate forms of the state machine exist for the two
different types of status reporting.
When operated without channel bonding (RXMODE[1] = LOW,
RX Modes 0 and 2), these state machines are disabled and
RXSTx[2:0] Priority
000
Description
Type-A Status
Normal Character Received.
The valid Data character on the output
bus meets all the formatting requirements of Data characters listed in
Table 29
.
Special Code Detected.
The valid special character on the output bus
meets all the formatting requirements of Special Code characters listed
in
Table 30
, but is not the presently selected framing character or a
decoder violation indication.
Receive Elasticity Buffer Under-
run/Overrun Error.
The receive
buffer was not able to add/drop a
K28.5 or framing character.
Type-B Status
Receive BIST Status
(Receive BIST = Enabled)
BIST Data Compare.
Charac-
ter compared correctly
7
001
7
BIST Command Compare.
Character compared correctly
010
2
Channel Lock Detected.
Asserts
when the bonded channels have
detected RESYNC within the allot-
ted window. Presented only on the
last cycle before aligned data is pre-
sented.
BIST Last Good.
Last Charac-
ter of BIST sequence detected
and valid.
011
5
Framing Character detected.
This indicates that a character matching
the patterns identified as a framing character (as selected by FRAM-
CHAR) was detected. The decoded value of this character is present in
the associated output bus.
Codeword Violation.
The character on the output bus is a C0.7. This
indicates that the received character cannot be decoded into any valid
character.
Loss of Sync.
The character on
the bus is invalid, due to an event
that has caused the receive chan-
nels to lose synchronization. When
channel bonding is enabled, this in-
dicates that one or more channels
have either lost bit synchronization
(loss of character framing), or that
the bonded channels are no longer
in proper character alignment.
When the channels are operated in-
dependently (with the decoder en-
abled), this indicates a PLL Out of
Lock condition.
100
4
BIST Last Bad.
Last Character
of BIST sequence detected in-
valid.
BIST Start.
Receive BIST is en-
abled on this channel, but char-
acter compares have not yet
commenced. This also indi-
cates a PLL Out of Lock condi-
tion, and Elasticity Buffer over-
flow/underflow conditions.
101
1
Loss of Sync.
The character on
the bus is invalid, due to an event
that has caused the receive chan-
nels to lose synchronization. When
channel bonding is enabled, this in-
dicates that one or more channels
have either lost bit synchronization
(loss of character framing), or that
the bonded channels are no longer
in proper character alignment.
When the channels are operated in-
dependently (with the decoder en-
abled), this indicates a loss of char-
acter framing. Also used to indicate
receive Elasticity Buffer under-
flow/overflow errors.
110
6
Running Disparity Error.
The character on the output bus is a C4.7,
C1.7, or C2.7.
BIST Error.
While comparing
characters, a mismatch was
found in one or more of the de-
coded character bits.
BIST Wait.
The receiver is com-
paring characters. but has not
yet found the start of BIST char-
acter to enable the LFSR.
111
3
Resync.
The receiver state machine is in the Resynchronization state.
In this state the data on the output bus reflects the presently decoded
FRAMCHAR.
相關PDF資料
PDF描述
CYP15G0403DXB Physical Layer Devices
CYP15G0101 Single-channel HOTLink Transceiver
CYP15G0101DXB Single-channel HOTLink Transceiver
CYP15G0101DXB-BBC Single-channel HOTLink Transceiver
CYP15G0101DXB-BBI Single-channel HOTLink Transceiver
相關代理商/技術參數
參數描述
CYP15G0101DXA-BBI 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Single Channel HOTLink II Transceiver
CYP15G0101DXB 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Single-channel HOTLink II⑩ Transceiver
CYP15G0101DXB_11 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Single-channel HOTLink II Transceiver Compliant to multiple standards
CYP15G0101DXB_12 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Single-channel HOTLink IIa?￠ Transceiver
CYP15G0101DXB-BBC 功能描述:電信線路管理 IC Single Channel XCVR 1.5Gbps Bckplane COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*