- 您現在的位置：買賣IC網 > PDF目錄379877 > celeron CPU with Mobile Module (Intel Corp.) processor Mobile Module Connector 2 (MMC-2) at 466 MHz and 433MHZ(工作頻率466和433兆赫茲帶連接器2處理器) PDF資料下載
參數資料
| 型號： | celeron CPU with Mobile Module |
| 廠商： | Intel Corp. |
| 英文描述： | processor Mobile Module Connector 2 (MMC-2) at 466 MHz and 433MHZ(工作頻率466和433兆赫茲帶連接器2處理器) |
| 中文描述： | 移動處理器模塊連接器2（MMC管理- 2），466 MHz和433MHz的（工作頻率466和433兆赫茲帶連接器2處理器） |
| 文件頁數： | 17/47頁 |
| 文件大?。?/td> | 410K |
| 代理商： | CELERON CPU WITH MOBILE MODULE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
Celeron
Processor Mobile Module MMC-2
at 466 MHz and 433 MHz
13
3.1.10
ITP/JTAG (9 Signals)
Table 10 lists the ITP/JTAG signals, which the system
manufacturer can use to implement a JTAG chain and an
ITP port if desired.
Table 10. ITP/JTAG Pins
Name
Type
Voltage
Description
TDO
O
V_CPUPU
JTAG Test Data Out:
Serial output port. TAP instructions and data are shifted out of the
processor from this port.
TDI
I
V_CPUPU
JTAG Test Data In:
Serial input port. TAP instructions and data are shifted into the
processor from this port.
TMS
I
V_CPUPU
JTAG Test Mode Select:
Controls the TAP controller change sequence.
TCLK
I
V_CPUPU
JTAG Test Clock:
Testability clock for clocking the JTAG boundary scan sequence.
TRST#
I
V_CPUPU
JTAG Test Reset:
Asynchronously resets the TAP controller in the processor.
FS_RESET#
O
GTL+
Processor Reset:
Processor reset status to the ITP.
VTT
O
V_CORE
GTL+ Termination Voltage:
Used by the POWERON pin on the ITP debug port to
determine when target system is on. POWERON pin is pulled up using a 1 K
resistor
to VTT.
FS_PREQ#
I
V_CPUPU
Debug Mode Request:
Driven by the ITP and makes request to enter debug mode.
FS_PRDY#
O
GTL+
Debug Mode Ready:
Driven by the processor and informs the ITP that the processor is
in debug mode.
NOTE:
DBREST# (reset target system) on the ITP debug port can be “l(fā)ogically ANDed” with VR_PWRGD TO PIIX4E/M’s PWROK.
3.1.11
Miscellaneous (82 Signals)
Table 11 lists the miscellaneous signal pins.
Table 11. Miscellaneous Pins
Name
Type
Number
Description
Module
ID[3:0]
O
CMOS
4
Module Revision ID
: These pins track the revision level of the Celeron processor
mobile module MMC-2. A 100-K pullup resistor to V_3S must be placed on the system
electronics for these signals. See Section 7.0, “Labeling Information” for more
information.
Ground
I
45
Ground.
Reserved
RSVD
33
Unallocated Reserved pins and should not be connected.
相關PDF資料 |
PDF描述 |
|---|---|
| Celeron Processor with mobile | Celeron Processor Mobile Module MMC-1 at 400 MHz, 366 MHz, 333 MHz, and 300 MHz(工作頻率400,366,333,300和266兆赫茲帶移動模塊和連接器1處理器) |
| celeron processor | 32 bit Celeron Processor Mobile Module(32 位帶移動模塊處理器) |
| CEM11C2 | Dual Enhancement Mode Field Effect Transistor (N and P Channel) |
| CEM2005 | Dual Enhancement Mode Field Effect Transistor(N and Channel) |
| CEM2030A | Dual Enhancement Mode Field Effect Transistor(N and P Channel) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CELF001001J1 | 制造商:Panasonic Industrial Company 功能描述:FILTER |
| CELHK11-1REC5-59-3.00-AV-01-V | 功能描述:CIRCUIT BRKR MAG-HYDR LEVER 3A 制造商:sensata technologies/airpax 系列:CEL 零件狀態:有效 斷路器類型:磁性（液力延遲） 額定電流:3A 額定電壓 - AC:- 額定電壓 - DC:- 極數:2 致動器類型:搖臂 照明:- 照明電壓（標稱值）:- 安裝類型:面板安裝 標準包裝:1 |
| CELHK11-1REC5-59-35.0-AV-01-V | 功能描述:CIRCUIT BRKR MAG-HYDR LEVER 35A 制造商:sensata technologies/airpax 系列:CEL 零件狀態:有效 斷路器類型:磁性（液力延遲） 額定電流:35A 額定電壓 - AC:- 額定電壓 - DC:- 極數:2 致動器類型:搖臂 照明:- 照明電壓（標稱值）:- 安裝類型:面板安裝 標準包裝:1 |
| CELHK11-1REC5-71165-10-V | 功能描述:CIRCUIT BREAKER MAG-HYDR LEVER 制造商:sensata technologies/airpax 系列:* 零件狀態:有效 標準包裝:1 |
| CELHK11-1REC5-71165-11-V | 功能描述:CIRCUIT BREAKER MAG-HYDR LEVER 制造商:sensata technologies/airpax 系列:* 零件狀態:有效 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。