參數資料
型號: ADUC7021BCPZ62-RL7
廠商: Analog Devices Inc
文件頁數: 48/92頁
文件大小: 0K
描述: IC MCU 12BIT 1MSPS UART 40-LFCSP
標準包裝: 750
系列: MicroConverter® ADuC7xxx
核心處理器: ARM7
芯體尺寸: 16/32-位
速度: 44MHz
連通性: EBI/EMI,I²C,SPI,UART/USART
外圍設備: PLA,PWM,PSM,溫度傳感器,WDT
輸入/輸出數: 13
程序存儲器容量: 64KB(32K x 16)
程序存儲器類型: 閃存
RAM 容量: 2K x 32
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 3.6 V
數據轉換器: A/D 8x12b,D/A 2x12b
振蕩器型: 內部
工作溫度: -40°C ~ 125°C
封裝/外殼: 40-VFQFN 裸露焊盤,CSP
包裝: 帶卷 (TR)
ADuC7019/20/21/22/24/25/26/27/28
Rev. B | Page 52 of 92
Example source code:
T2LD = 5;
TCON = 0x480;
while ((T2VAL == t2val_old) || (T2VAL >
3)) //ensures timer value loaded
IRQEN = 0x10;
//enable T2 interrupt
PLLKEY1 = 0xAA;
PLLCON = 0x01;
PLLKEY2 = 0x55;
POWKEY1 = 0x01;
POWCON = 0x27;
// Set Core into Nap mode
POWKEY2 = 0xF4;
In noisy environments, noise can couple to the external crystal
pins, and PLL may lose lock momentarily. A PLL interrupt is
provided in the interrupt controller. The core clock is immediately
halted, and this interrupt is only serviced when the lock is restored.
In case of crystal loss, the watchdog timer should be used. During
initialization, a test on the RSTSTA can determine if the reset
came from the watchdog timer.
External Clock Selection
To switch to an external clock on P0.7, configure P0.7 in
Mode 1. The external clock can be up to 44 MHz, providing
the tolerance is 1%.
Example source code:
T2LD = 5;
TCON = 0x480;
while ((T2VAL == t2val_old) || (T2VAL >
3)) //ensures timer value loaded
IRQEN = 0x10;
//enable T2 interrupt
PLLKEY1 = 0xAA;
PLLCON = 0x03; //Select external clock
PLLKEY2 = 0x55;
POWKEY1 = 0x01;
POWCON = 0x27;
//
Set Core into Nap mode
POWKEY2 = 0xF4;
Power Control System
A choice of operating modes is available on the ADuC7019/20/
21/22/24/25/26/27/28. Table 31 describes what part is powered
on in the different modes and indicates the power-up time.
Table 32 gives some typical values of the total current consump-
tion (analog + digital supply currents) in the different modes,
depending on the clock divider bits. The ADC is turned off. Note
that these values also include current consumption of the
regulator and other parts on the test board where these values
are measured.
Table 31. Operating Modes
Mode
Core
Peripherals
PLL
XTAL/T2/T3
IRQ0 to IRQ3
Start-Up/Power-On Time
Active
X
130 ms at CD = 0
Pause
X
24 ns at CD = 0; 3 μs at CD = 7
Nap
X
24 ns at CD = 0; 3 μs at CD = 7
Sleep
X
1.58 ms
Stop
X
1.7 ms
Table 32. Typical Current Consumption at 25°C in mA.
PC[2:0]
Mode
CD = 0
CD = 1
CD = 2
CD = 3
CD = 4
CD = 5
CD = 6
CD = 7
000
Active
33.1
21.2
13.8
10
8.1
7.2
6.7
6.45
001
Pause
22.7
13.3
8.5
6.1
4.9
4.3
4
3.85
010
Nap
3.8
011
Sleep
0.4
100
Stop
0.4
相關PDF資料
PDF描述
ADUC7023BCPZ62I-R7 IC MCU 12BIT 62KB FLASH 32LFCSP
ADUC7024BCPZ62 IC MCU FLSH 62K ANLG I/O 64LFCSP
ADUC7032BSTZ-88 IC MCU 96K FLASH DUAL 48LQFP
ADUC7032BSTZ-8V-RL IC BATTERY SENSOR PREC 48-LQFP
ADUC7034BCPZ IC MCU FLASH 32K ANLG IO 48LFCSP
相關代理商/技術參數
參數描述
ADUC7022 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7022ACP32 制造商:Analog Devices 功能描述:FLASH ARM7+10-CH,12-B ADC IC - Trays
ADUC7022ACPZ32 制造商:Analog Devices 功能描述:MCU 32BIT RISC 32KB FLASH 3.3V 40LFCSP EP - Trays
ADUC7022BCP32 制造商:Analog Devices 功能描述:FLASH ARM7+10-CH,12-B ADC IC - Trays
ADUC7022BCP62 制造商:Analog Devices 功能描述:FLASH ARM7+10-CH,12-B ADC IC - Trays