TABLE
參數資料
型號： XRT86VL30IV-F
廠商： Exar Corporation
文件頁數： 16/175頁
文件大?。?/td> 0K
描述： IC FRAMR/LIU T1/E1/J1 QD 128LQFP
標準包裝： 72
控制器類型： T1/E1/J1 調幀器，LIU
電源電壓： 3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-LQFP（14x20）
包裝： 托盤
其它名稱： 1016-1485
XRT86VL30IV-F-ND
XRT86VL30
107
SINGLE T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
REV. 1.0.1
TABLE 98: FRAMER INTERRUPT STATUS REGISTER (FISR)
HEX ADDRESS: 0X0B04
BIT
FUNCTION
TYPE
DEFAULT
DESCRIPTION-OPERATION
7-6
-
Reserved (For E1 mode only)
5
SIG
RUR/
WC
0
Change in Signaling Bits Interrupt Status
This Reset-Upon-Read bit field indicates whether or not the “Change in
Signaling Bits” interrupt has occurred since the last read of this register.
If this interrupt is enabled, then the Receive T1 Framer block will generate
an interrupt whenever any one of the four signaling bits values (A,B,C,D)
has changed in any one of the 24 channels within the incoming T1
frames. Users can read the signaling change registers (address 0x010D-
0x010F) to determine which signalling channel has changed.
0 = Indicates that the “Change in Signaling Bits” interrupt has not occurred
since the last read of this register.
1 = Indicates that the “Change in Signaling Bits” interrupt has occurred
since the last read of this register.
NOTE: This bit only has meaning when Robbed-Bit Signaling is enabled.
4
COFA
RUR/
WC
0
Change of Frame Alignment (COFA) Interrupt Status
This Reset-Upon-Read bit field indicates whether or not the “Change of
Framing Alignment (COFA)” interrupt has occurred since the last read of
this register. If this interrupt is enabled, then the Receive T1 Framer block
will generate an interrupt whenever the Receive T1 Framer block detects
a Change of Framing Alignment Signal (e.g., the Framing bits have
appeared to move to a different location within the incoming T1 data
stream).
0 = Indicates that the “Change of Framing Alignment (COFA)” interrupt
has not occurred since the last read of this register.
1 = Indicates that the “Change of Framing Alignment (COFA)” interrupt
has occurred since the last read of this register.
3
OOF_Status
RUR/
WC
0
Change in Receive Out of Frame Defect Condition Interrupt Status.
This Reset-Upon-Read bit field indicates whether or not the “Change in
Receive Out of Frame Defect Condition” interrupt has occurred since the
last read of this register.
Out of Frame defect condition is declared when “TOLR” out of “RANG”
errors in the framing bit pattern is detected. (Register 0x010B)
If this interrupt is enabled, then the Receive T1 Framer block will generate
an interrupt in response to either one of the following conditions.
1. Whenever the Receive T1 Framer block declares the Out of Frame
defect condition.
2. Whenever the Receive T1 Framer block clears the Out of Frame
defect condition
0 = Indicates that the “Change in Receive Out of Frame defect condition”
interrupt has not occurred since the last read of this register
1 = Indicates that the “Change in Receive Out of Frame defect condition”
interrupt has occurred since the last read of this register
相關PDF資料
PDF描述
XRT86VL32IB-F IC LIU/FRAMER T1/E1/J1 2CH 225BG
XRT86VL34IB-F IC LIU/FRAMER T1/E1/J1 4CH 225BG
XRT86VL38IB484-F IC LIU/FRAMER T1/E1/J1 8CH 484BG
XRT86VX38IB329-F IC TI/E1/J1 FRAMER/LIU 329FPBGA
XRT94L31IB-L IC MAPPER DS3/E3/STS-1 504TBGA
相關代理商/技術參數
參數描述
XRT86VL30IV-F 制造商:Exar Corporation 功能描述:T1/E1 Framer Combo IC
XRT86VL32 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VL32_07 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION
XRT86VL32_0709 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
XRT86VL32_1 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*