- 您現在的位置：買賣IC網 > PDF目錄1976 > XRT72L71IQ (Exar Corporation)IC FRAMER DS3 ATM UNI 160PQFP PDF資料下載
參數資料
| 型號： | XRT72L71IQ |
| 廠商： | Exar Corporation |
| 文件頁數： | 53/102頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FRAMER DS3 ATM UNI 160PQFP |
| 產品變化通告： | XRT72Lx Series Obsolescence 02/May/2012 |
| 標準包裝： | 24 |
| 控制器類型： | DS3 ATM UNI，透明通道調幀器 |
| 電源電壓： | 3.3V |
| 電流 - 電源： | 120mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 160-BQFP |
| 供應商設備封裝： | 160-PQFP（28x28） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
XRT72L71
á
DS3 ATM UNI/CLEAR CHANNEL FRAMER
REV. 1.1.0
50
TABLE 7: TEST CELL CONTROL AND STATUS REGISTER
REGISTER 6
TEST CELL CONTROL AND STATUS REGISTER
HEX ADDRESS: 0X06
BIT
FUNCTION
TYPE
DEFAULT
DESCRIPTION-OPERATION
7
CLEAR CHANNEL
ENABLE
R/W
0
0: Configures the XRT72L71 to operate in the “ATM UNI” Mode.
1: Configures the XRT72L71 to operate in the “Clear Channel Mode”
6
Tx Overheard Extracted
Data Input
R/W
0
0: Transmit Payload Data Interface does not accept overhead bits via the
“TxSerData” input pin
1: Transmit Payload Data Input Interface block accepts overhead bits via the
“TxSerData” input pin.
NOTE: This register is only active if the XRT72L71 has been configured to
operate in the “ATM UNI” Mode.
5Unused
RO
0
4
TEST CELL ENABLE/
PRBS ENABLE
R/W
0
If the XRT72L71 has been configured to operate in the ATM UNI Mode:
0: Disables the Test Cell Generator and Receiver
1: Enables the Test Cell Generator and Receiver. The test cell Generator will
begin generating an inserting “Test Cell” into the “outbound” DS3 data
stream. The Test Cell Receiver will begin to “l(fā)ook for” Test Cells, and acquire
a PRBS pattern with the “payload bytes” of these test cells.
If the XRT72L71 has beenconfigured to operate in the “Clear Channel
Framer” Mode:
0: Disables the PRBS Generator and Receiver
1: Enables the PRBS Generator and Receiver. The PRBS Generator will
begin to insert a “PRBS” pattern into the “outbound” DS3 data strream. The
PRBS Receiver will begin to “l(fā)ook” for this PRBS pattern and acquire “PRBS
Lock”
3
Reserved
R/W
0
This bit-field is unused
2
ONE-SHOT TEST
R/W
0
O: Continous Mode - Test cells are generated as long as the “TEST CELL
ENABLE” bit is high
1: Burst Mode - 0 to 1 transition in the “TEST CELL ENABLE” bit results in
the generation of 1024 test cells.
NOTE: This register is only active if the XRT72L71 has been configured to
operate in the “ATM UNI” Mode.
1
ONE SHOT DONE
RO
0
0: Test Cell Generator is currently generating its burst of 1024 Test Cells.
1: Test Cell Generator has completed generating its “l(fā)atest” burst of 1024
Test Cells. This bit-field is reset when a new cycle is begun by a 0 to 1 tran-
sition within the “TEST CELL ENABLE” bit-field.
NOTE: This bit-field is only active if both of the following conditions are true.
1. The XRT72L71 has been configured to operate in the
“ATM UNI Mode
2. The Test Cell Generator/Receiver has been configured
to operate in the “Burst” Mode.
0
PRBS LOCK
RO
0
0: The Test Cell Receiver (for “ATM UNI” Applications” or the PRBS Receiver
(for “Clear-Channel Framer” applications) has not yet acquired “Pattern Lock”
with the “PRBS” data bening generated by the Test Cell Generator/PRBS
Generator.
1: The Test Cell Receiver/PRBS Receiver has been able to acquire Pattern
Lock with the PRBS data being generated by the Test Cell Generator.
NOTE: Once the Test Cell Receiver/PRBS Receiver has acquired PRBS
Lock, then it will begin to record “Pattern Bit Error” events within the Test Cell
Error Count (or PRBS Error Count) Registers.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L02MIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| XRT73L03BIV-F | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| XRT73L04BIV-F | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| XRT73L06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73LC00AIV-F | IC LIU STS1/DS3/E3 SGL 44TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT72L71IQ-F | 功能描述:網絡控制器與處理器 IC Single CH DS3 UNI (3.3V) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT72L73IB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XRT72L74IB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XRT7300 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT7300ES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。