- 您現在的位置：買賣IC網 > PDF目錄385017 > TSB41BA3AIGGM (Texas Instruments, Inc.) IEEE 1394b THREE-PORT CABLE TRANSCEIVER/ARBITER PDF資料下載
參數資料
| 型號： | TSB41BA3AIGGM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | IEEE 1394b THREE-PORT CABLE TRANSCEIVER/ARBITER |
| 中文描述： | 的IEEE 1394b三端口電纜收發器/仲裁者 |
| 文件頁數： | 35/66頁 |
| 文件大小： | 895K |
| 代理商： | TSB41BA3AIGGM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
SLLS618B JUNE 2004 REVISED AUGUST 2004
35
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
bus reset (continued)
Therefore, in order to maintain consistent gap-counts throughout the bus, the following rules apply to the use
of the IBR bit, RHB bit, and gap-count in PHY register 1:
Following the transmission of a PHY configuration packet, a bus reset must be initiated in order to verify
that all nodes have correctly updated their RHB bits and gap-count values, and to ensure that a subsequent
new connection to the bus causes the gap-count to be set to 63 on all nodes in the bus. If this bus reset is
initiated by setting the IBR bit to 1, then the RHB bit and gap-count register must also be loaded with the
correct values consistent with the just transmitted PHY configuration packet. In the TSB41BA3A, the RHB
bit and gap-count have been updated to their correct values upon the transmission of the PHY configuration
packet and so these values may first be read from register 1 and then rewritten.
Other than to initiate the bus reset, which must follow the transmission of a PHY configuration packet,
whenever the IBR bit is set to 1 in order to initiate a bus reset, the gap-count value must also be set to 63
so as to be consistent with other nodes on the bus and the RHB bit must be maintained with its current value.
The PHY register 1 must not be written to except to set the IBR bit. The RHB bit and gap-count must not
be written without also setting the IBR bit to 1.
To avoid these problems all bus resets initiated by software must be initiated by writing the ISBR bit (bit 1
PHY register 0101b). Care must be taken to not change the value of any of the other writeable bits in this
register when the ISBR bit is written to. Also, the only means to change the gap count of any node must
be by means of the PHY configuration packet, which changes all nodes to the same gap count.
相關PDF資料 |
PDF描述 |
|---|---|
| TSC2100IDAR | PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH INTEGRATED STEREO AUDIO CODEC AND HEADPHONE/SPEAKER AMPLIFIER |
| TSC2300IPAGR | PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH AUDIO CODEC |
| TSC2301IGQZ | PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
| TSC2301PAG | SIGN, EYE PROTECTION MUST BE WORN; RoHS Compliant: NA |
| TSC2301PAGR | PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSB41BA3AIPFP | 功能描述:緩沖器和線路驅動器 Three-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| TSB41BA3APFP | 功能描述:緩沖器和線路驅動器 Three-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| TSB41BA3APFPG4 | 功能描述:1394 接口集成電路 Three-Port Cable Xcvr/Arbiter RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB41BA3ATPFPEP | 功能描述:緩沖器和線路驅動器 Mil Enh 3-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| TSB41BA3B | 制造商:TI 制造商全稱:Texas Instruments 功能描述:IEEE 1394b THREE-PORT CABLE TRANSCEIVER/ARBITER |
發布緊急采購，3分鐘左右您將得到回復。