- 您現在的位置：買賣IC網 > PDF目錄384999 > TMC428 (Electronic Theatre Controls, Inc.) Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces PDF資料下載
參數資料
| 型號： | TMC428 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces |
| 中文描述： | 三步進電機智能控制器的串行外圍接口 |
| 文件頁數： | 5/50頁 |
| 文件大?。?/td> | 378K |
| 代理商： | TMC428 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
TMC428 DATA SHEET (V. 1.00 / February 12, 2001)
5
Copyright 2000, TRINAMIC Microchips GmbH
M I C R O C H I P S
5
send back from the stepper motor driver chain to the TMC428 are buffered within two 24 bit wide
registers. The micro controller has direct access to these registers. Although, the TMC428 provides
datagrams with up to 64 bits, only the last 48 bits send back from the driver chain are buffered for read
out by the micro controller. This is because buffering of 3 time 16 bits is sufficient for a chain of three
TMC288 stepper motor drivers (see Figure 1) and most other drivers– also from other vendors –sending
back up to 16 bits.
From the user’s point of view, the TMC428 consists of a set of registers, accessed by an micro controller
(μC) via a serial interface in an uniform way. Each time, a μC sends a datagram to the TMC428, it
simultaneously receives a datagram from the TMC428. Each datagram contains all necessary information
to address and to select between read and write for both, the registers and the on-chip memory. This
simplifies the communication with the TMC428 and makes the programming easy. Some micro controllers
have a SPI
of the TMC428. For micro controllers without SPI
sending a 32 bit vector via a serial four wire interface if called, returning that 32 bit vector received from
the TMC428.
TM
hardware interface, which directly connects to the serial four wire micro controller interface
TM
hardware interface one just has to write a subroutine
Notation of Number Systems
Decimal numbers are used as usual without additional identification. Binary numbers are identified by a
prefixed % character. Hexadecimal numbers are identified by a prefixed $ character. So, for example the
decimal number 42 in the decimal system is written as %101010 in the binary number system, and it is
written as $2A in the hexadecimal number system.
相關PDF資料 |
PDF描述 |
|---|---|
| TMD0305-2 | Microwave Power GaAs MMIC(微波功率砷化鎵MMIC) |
| TMD1414-2C | MICROWAVE POWER MMIC AMPLIFIER |
| TMD3438-1 | Microwave Power MMIC Amplifier(微波功率MMIC（單片式微波集成電路）放大器) |
| TMG5CQ60F | TRIAC(Through Hole/Isolated) |
| TMM23256P | 256K BIT(32K WORD x 8 BIT) MASK ROM N-CHANNEL SILICON GATE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC428_06 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces |
| TMC4281GT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4281TT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4282GT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4282TT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
發布緊急采購，3分鐘左右您將得到回復。