參數資料
型號： TMC428
廠商： Electronic Theatre Controls, Inc.
英文描述： Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces
中文描述： 三步進電機智能控制器的串行外圍接口
文件頁數： 7/50頁
文件大?。?/td> 378K
代理商： TMC428
TMC428 DATA SHEET (V. 1.00 / February 12, 2001)
7
Copyright 2000, TRINAMIC Microchips GmbH
M I C R O C H I P S
7
Functional Description and Block Diagram
From the user’s point of view, the TMC428 consists of a set of registers of different units and on-chip
RAM (see. Figure 4), accessed via the serial μC interface in an uniform way. The serial interface to the
micro controller is easy to use. It uses just a simple protocol with fixed length datagrams for read and write
access. The serial interface to the stepper motor driver chain has to be configured by an initialization
sequence which writes the configuration into the on-chip RAM. Once configured the serial driver interface
works autonomously. The internal multiple port RAM controller of the TMC428 autonomously takes care
of access scheduling. So, the user may read and write both, registers and on-chip RAM at any time. The
registers hold global configuration parameters and the motion parameters. The on-chip RAM stores the
configuration of the serial driver interface and the micro step table.
The ramp generator monitors the motion parameters stored in its registers. If required, it generates step
pulses automatically taking user defined motion parameter limits into account. The serial driver interface
automatically sends datagrams to the stepper motor driver chain on demand. The ramp generator
calculates velocity profiles controlling the pulse generator. The micro step unit (including sequencer)
processes step pulses from the pulse generator– representing micro steps, half steps, or full steps
depending on the selected step resolution –and makes the results available to the serial driver interface.
The ramp generator also interfaces the reference switch inputs. Unused reference switches have to be
connected to ground. A pull-down resistor is necessary at the SDI_S input of the TMC428 for those serial
peripheral interface stepper motor drivers that set their serial data output to high impedance ‘Z’ while
inactive.
The interrupt controller continuously watches reference switches and ramp generator conditions and
generates an interrupt if required. To save pins, the interrupt signal is multiplexed to the SDO_C signal.
This signal becomes the low active interrupt signal called nINT while nSCS_C is high (see Figure 5). So, if
the micro controller disables the interrupt during access to the TMC428 and enables the interrupt
otherwise, the multiplexed interrupt output of the TMC428 behaves like a dedicated interrupt output. For
polling, the TMC428 sends the status of the interrupt signal to the micro controller with each datagram.
To drive a stepper motor to a new target position, the user just overwrites the target position of that
stepper motor by sending a datagram to the TMC428. To run a stepper motor with a target velocity, the
user just writes it into a register assigned to a stepper motor.
nSCS_C
SCK_C
SDI_C
SDO_C
serial μC interface
CLK
TEST
multiple
ported RAM
interrupt
controller
serial driver interface
nSCS_S
SCK_S
SDO_S
SDI_S
[nSCS3]
[nSCS2]
10K
micro step unit
( including
sequencer )
ramp generator
&
pulse generator
R
R
R
voltage
regulator
V5
GND
V33
470nF
power-on
reset
Figure 4: TMC428 functional block diagram
相關PDF資料
PDF描述
TMD0305-2 Microwave Power GaAs MMIC(微波功率砷化鎵MMIC)
TMD1414-2C MICROWAVE POWER MMIC AMPLIFIER
TMD3438-1 Microwave Power MMIC Amplifier(微波功率MMIC（單片式微波集成電路）放大器)
TMG5CQ60F TRIAC(Through Hole/Isolated)
TMM23256P 256K BIT(32K WORD x 8 BIT) MASK ROM N-CHANNEL SILICON GATE
相關代理商/技術參數
參數描述
TMC428_06 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces
TMC4281GT 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS
TMC4281TT 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS
TMC4282GT 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS
TMC4282TT 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*