參數資料
型號： TMC428
廠商： Electronic Theatre Controls, Inc.
英文描述： Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces
中文描述： 三步進電機智能控制器的串行外圍接口
文件頁數： 9/50頁
文件大?。?/td> 378K
代理商： TMC428
TMC428 DATA SHEET (V. 1.00 / February 12, 2001)
9
Copyright 2000, TRINAMIC Microchips GmbH
M I C R O C H I P S
9
The signal nSCS_C has to be assigned at least three clock cycles (tSUCSC) high before sending a 32 bit
datagram. To initiate a transmission, the signal nSCS_C has to be set to low. Three clock cycles later
(tHDCSC) the serial data clock may go low. The most significant bit (MSB) of a 32 bit wide datagram
comes first and the least significant bit (LSB) is transmitted as the last one. To complete the data
transmission the serial data clock SCK_C has to set to high first and at least three clock cycles later, the
signal nSCS_C has to be assigned to high. So, nSCS_C and SCK_C change in opposite order from low to
high at the end of a transmission as these signals change from high to low at the beginning.
Automatic Power-On Reset
The TMC428 performs an automatic power-on reset (see ). To be sure, that the power-on reset has been
completed before starting communication with the TMC428, one should wait at least for 10 μs before
sending the first datagram, which is approximately one datagram at 16 MHz clock frequency
(tDATAGRAM16MHzMin = (1+32+1) * 6 / 16 MHz = 12.75 μs).
Serial Peripheral Interface to Stepper Motor Driver Chain
The timing of the serial stepper motor interface is similar to that of the micro controller interface. It
directly connects to SPI
for each stepper motor driver chip of the daisy chain. From the micro controllers point of view, it simply
sends a fixed sequence of datagrams to the TMC428 to initialize it after power-up. Once initialized by the
micro controller, the TMC428 autonomously generates the datagrams for the stepper motor driver daisy
chain without any additional interventions of the micro controller.
TM
smart power stepper motor drivers. The bit mapping is configurable individually
CLK
tCLK
SCK_S
nSCS_S
SDI_S
SDO_S
sdi_s_bit#0
tPD
tPD
tPD
1 x sampled SDI_S
tSUSCS
tHDSCS
tCKSL
tCKSH
sdo_s_bit#0
sdi_s_bit#n-1
sdo_s_bit#n-1
sdo_s_bit#1
sdi_s_bit#1
sdo_s_bit#n
sdi_s_bit#n
m datagram bits
one full stepper motor driver datagram
tDATAGRAMdrv
1 x sampled SDI_S
m x sampled SDI_S
Figure 6: Timing diagram of the serial stepper motor driver interface
相關PDF資料
PDF描述
TMD0305-2 Microwave Power GaAs MMIC(微波功率砷化鎵MMIC)
TMD1414-2C MICROWAVE POWER MMIC AMPLIFIER
TMD3438-1 Microwave Power MMIC Amplifier(微波功率MMIC（單片式微波集成電路）放大器)
TMG5CQ60F TRIAC(Through Hole/Isolated)
TMM23256P 256K BIT(32K WORD x 8 BIT) MASK ROM N-CHANNEL SILICON GATE
相關代理商/技術參數
參數描述
TMC428_06 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces
TMC4281GT 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS
TMC4281TT 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS
TMC4282GT 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS
TMC4282TT 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*