- 您現在的位置：買賣IC網 > PDF目錄384999 > TMC428 (Electronic Theatre Controls, Inc.) Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces PDF資料下載
參數資料
| 型號： | TMC428 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces |
| 中文描述： | 三步進電機智能控制器的串行外圍接口 |
| 文件頁數： | 20/50頁 |
| 文件大小： | 378K |
| 代理商： | TMC428 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
TMC428 DATA SHEET (V. 1.00 / February 12, 2001)
20
Copyright 2000, TRINAMIC Microchips GmbH
M I C R O C H I P S
20
To represent the parameter
p = p_mul / p_div = (128+pmul) / 2^(3+pdiv)
one just has to find a pair of
pmul
and
pdiv
that approximates
p
, with
pmul
in range
0 ... 127
and
pdiv
one of
{8, 16 , 32 ,64 ,128 ,
256, 512, 1024, 2048, 4096, 8192, 16384, 32786, 65536}
. There are only 128 * 14 = 1792 pairs of
(pmul, pdiv)
. So, one can simply try all possible pairs
(pmul, pdiv)
with a program and choose one pair.
To find one pair, one has to calculate
p = a_max / ( 128 * 2^( ramp_div-pulse_div ) )
and
p’ = p_mul / p_div = (128+pmul) / 2^(3+pdiv)
and
q = p / p’
for each pair
(pmul , pdiv)
and select one pair for that
1.0 < q < 0.95
is valid. So, the value
q
interpreted
as a function
q(a_max, ramp_div, pulse_div, pmul, pdiv)
gives the quality criterion required. Although
q
= 1.0
indicates that
(pmul , pdiv)
perfectly represents the desired
p
for a given
a_max
, this could
cause overshooting because of finite numerical precision. In case of high resolution micro stepping,
overshooting of one micro step is negligible, if it is below the micro step resolution of a stepper motor. To
avoid overshooting, one can use
pmul-1
instead of the selected
pmul
. An example program in C
language can be found on page 47.
lp & ref_conf & ramp_mode (rm) (IDX=%1010)
The bit vectors
ref_conf
and
ramp_mode
are accessed via a common address, because these parameters
normally are initialized only once. The bit called
lp
(latched position) is a read only status bit. The TMC428
has three reference switch inputs. Without additional hardware, three reference switches are available. Per
default, each reference switch input is assigned individually to each stepper motor as a left reference
switch. The reference switch input REF3 can alternatively be assigned as the right reference switch of
stepper motor number one. In that configuration
a left and a right reference switch
is assigned to stepper
motor one, a left reference switch is assigned to stepper motor two, and no reference switch is assigned
to stepper motor three. The bit named
mot1r
in the stepper motor global parameter register (rrs=1 &
address=111111) selects one of these configurations. With additional hardware, up to six reference
switches– a left and a right one assigned to each stepper motor –are supported (see Figure 11). The
additional hardware is just a 74HC157, where three of four 2-to-1-multiplexers are used. The feature of
multiplexing is controlled by the bit named
refmux
in the stepper motor global parameter register (rrs=1
& address=111111).
The two least significant bits on this address named
ramp_mode (rm)
select one of the four possible
stepping modes:
00 : RAMP_MODE
01 : SOFT_MODE
10 : VELOCITY_MODE
11 : HOLD_MODE
The mode called
RAMP_MODE
is proposed as the default mode for positioning tasks, where the
VELOCITY_MODE
is the default for applications, where stepper motors have to be driven precisely with
constant velocity. The
SOFT_MODE
is similar to the standard
RAMP_MODE
except that the target
position is approached quite slowly, but this feature could be useful for those applications where
vibrations at the target positions have to be minimized. The
HOLD_MODE
is proposed for motion control
applications, where the ramp generation is completely controlled by the micro controller.
相關PDF資料 |
PDF描述 |
|---|---|
| TMD0305-2 | Microwave Power GaAs MMIC(微波功率砷化鎵MMIC) |
| TMD1414-2C | MICROWAVE POWER MMIC AMPLIFIER |
| TMD3438-1 | Microwave Power MMIC Amplifier(微波功率MMIC（單片式微波集成電路）放大器) |
| TMG5CQ60F | TRIAC(Through Hole/Isolated) |
| TMM23256P | 256K BIT(32K WORD x 8 BIT) MASK ROM N-CHANNEL SILICON GATE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC428_06 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces |
| TMC4281GT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4281TT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4282GT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4282TT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
發布緊急采購，3分鐘左右您將得到回復。