- 您現在的位置：買賣IC網 > PDF目錄384999 > TMC428 (Electronic Theatre Controls, Inc.) Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces PDF資料下載
參數資料
| 型號： | TMC428 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces |
| 中文描述： | 三步進電機智能控制器的串行外圍接口 |
| 文件頁數： | 23/50頁 |
| 文件大?。?/td> | 378K |
| 代理商： | TMC428 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
TMC428 DATA SHEET (V. 1.00 / February 12, 2001)
23
Copyright 2000, TRINAMIC Microchips GmbH
M I C R O C H I P S
23
R[Hz] = f_clk[Hz] * velocity / ( 2^pulse_div * 2048 * 32 )
where
f_clk[Hz]
is the frequency of the external clock signal. The parameter velocity is in range 0 to 2047.
The pulse generator of the TMC428 generates one step pulse with each pulse generator clock pulse if the
velocity is set to 2047. The change
D
R
in the pulse rate per time unit (step frequency change per second –
the acceleration) is given by
D
R[Hz/s] = f_clk[Hz] * a_max / 256 / ( 2^ramp_div * 2048 * 32 ).
The parameter a_max is in range 0 to 2047. So, the parameter
ramp_div
scales the acceleration
parameter
a_max
, where the parameter
pulse_div
scales the velocity parameters.
usrs
[micro steps /
full step]
significant DAC bits
(controlling current
amplitude)
-
5 (MSB)
5 (MSB), 4
5 (MSB), 4, 3
5 (MSB), 4, 3, 2
5 (MSB), 4, 3, 2, 1
5 (MSB), 4, 3, 2, 1, 0 (LSB)
5 (MSB), 4, 3, 2, 1, 0 (LSB)
comment
0
0
0
1
2
4
8
full step (constant current amplitude)
half step
0
0
1
0
1
0
0
1
1
1
0
0
16
32
64
64
1
0
1
1
1
0
1
1
1
micro stepping
Table 10 – micro step resolution selection (usrs) parameter
The three bit wide parameter
usrs
(
μ s
tep
r
esolution
s
election
)
determines the micro step resolution for its
associated stepper motor according to Table 10. There is a individual set of 6 DAC bits proposed for each
of the two phases (coils) for current control to provide up to 64 micro steps per full step. Depending on
the micro step resolution, a sub set of 6 DAC bits are significant. Using full stepping, the current amplitude
is constant for both phases (coils) of a stepper motor and the polarity of one phase (coil) changes with
each full step. The micro step counters are initialized by 0 during power-on reset. With each micro step an
associated counter accumulates the programmed micro step resolution value
usrs
.
dx_ref_tolerance (IDX=%1101)
To allow the motor to drive near the reference point, it is possible to exclude a range of steps from the
stop switch function. This parameter is important to disable stopping forced by reference switches during
reference position search. The parameter affects interrupt conditions as described before.
x_latched (IDX=%1110)
This read-only register stores the actual position if a change of the reference switch is detected. The
reference switch is defined by the bit REF_RnL of the configuration register lp & ref_conf & ramp_mode
(IDX=%1010). To initialize this position storage mechanism one simply has to write to the (read-only)
register. Then the actual position is saved in the register with the next change of the reference switch
status. The bit lp signals if latching of the position is pending.
相關PDF資料 |
PDF描述 |
|---|---|
| TMD0305-2 | Microwave Power GaAs MMIC(微波功率砷化鎵MMIC) |
| TMD1414-2C | MICROWAVE POWER MMIC AMPLIFIER |
| TMD3438-1 | Microwave Power MMIC Amplifier(微波功率MMIC（單片式微波集成電路）放大器) |
| TMG5CQ60F | TRIAC(Through Hole/Isolated) |
| TMM23256P | 256K BIT(32K WORD x 8 BIT) MASK ROM N-CHANNEL SILICON GATE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC428_06 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Intelligent Triple Stepper Motor Controller with Serial Peripheral Interfaces |
| TMC4281GT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4281TT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4282GT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
| TMC4282TT | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:SCREW MACHINE SOCKETS & TERMINAL STRIPS |
發布緊急采購，3分鐘左右您將得到回復。