- 您現在的位置：買賣IC網 > PDF目錄98146 > ST92186B3BK (STMICROELECTRONICS) 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PDIP32 PDF資料下載
參數資料
| 型號： | ST92186B3BK |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PDIP32 |
| 封裝： | PLASTIC, SDIP-32 |
| 文件頁數： | 40/148頁 |
| 文件大?。?/td> | 1664K |
| 代理商： | ST92186B3BK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
134/148
ST92186B - A/D CONVERTER (A/D)
A/D CONVERTER (Cont’d)
The conversion technique used is successive ap-
proximation, with AC coupled analog fully differen-
tial comparators blocks plus a Sample and Hold
logic and a reference generator.
The internal reference (DAC) is based on the use
of a binary-ratioed capacitor array. This technique
allows the specified monotonicity (using the same
ratioed capacitors as sampling capacitor). A Pow-
er Down programmable bit sets the A/D converter
analog section to a zero consumption idle status.
7.8.3.1 Operating Modes
The two main operating modes, single and contin-
uous, can be selected by writing 0 (reset value) or
1 into the CONT bit of the Control Logic Register.
Single Mode
In single mode (CONT=0 in ADCLR) the STR bit is
forced to '0' after the end of channel i-th conver-
sion; then the A/D waits for a new start event. This
mode is useful when a set of signals must be sam-
pled at a fixed frequency imposed by a Timer unit
or an external generator (through the alternate
synchronization feature). A simple software rou-
tine monitoring the STR bit can be used to save
the current value before a new conversion ends
(so to create a signal samples table within the in-
ternal memory or the Register File). Furthermore,
if the R242.0 bit (register AD-INT, bit 0) is set, at
the end of conversion, a negative edge on the con-
nected external interrupt channel (see Interrupts
Chapter) is generated to allow the reading of the
converted data by means of an interrupt routine.
Continuous Mode
In continuous mode (CONT=1 in ADCLR) a con-
tinuous conversion flow is entered by a start event
on the selected channel until the STR bit is reset
by software.
At the end of each conversion, the Data Register
(ADCDR) content is updated with the last conver-
sion result, while the former value is lost. When the
conversion flow is stopped, an interrupt request is
generated with the same modality previously de-
scribed.
7.8.3.2 Alternate Synchronization
This feature is available in both single/continuous
modes. The negative edge of external EXTRG sig-
nal can be used to synchronize the conversion
start with a trigger pulse. This event can be ena-
bled or masked by programming the TRG bit in the
ADCLR Register.
The effect of alternate synchronization is to set the
STR bit, which is cleared by hardware at the end of
each conversion in single mode. In continuous
mode any trigger pulse following the first one will
be ignored. The synchronization source must pro-
vide a pulse (1.5 internal system clock, 125ns @
12 MHz internal clock) of minimum width, and a
period greater (in single mode) than the conver-
sion time (~6.5us @ 12 MHz internal clock). If a
trigger occurs when the STR bit is still '1' (conver-
sions still in progress), it is ignored (see Electrical
Characteristics).
Warning: If the EXTRG signal is already active
when TRG bit is set, the conversion starts immedi-
ately.
7.8.3.3 Power-Up Operations
Before enabling any A/D operation mode, set the
POW bit of the ADCLR Register at least 60 s be-
fore the first conversion starts to enable the bias-
ing circuits inside the analog section of the con-
verter. Clearing the POW bit is useful when the
A/D is not used so reducing the total chip power
consumption. This state is also the reset configu-
ration and it is forced by hardware when the core is
in HALT state (after a HALT instruction execution).
相關PDF資料 |
PDF描述 |
|---|---|
| ST92195B2T1/XXX | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP64 |
| ST92195B3B1/XXX | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PDIP56 |
| ST92195B4B1/XXX | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PDIP56 |
| ST92195B5T1/XXX | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP64 |
| ST92195B6T1/XXX | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST92195 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32-64K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY AND TELETEXT DATA SLICER |
| ST92195B | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32-64K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY AND TELETEXT DATA SLICER |
| ST92195B1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32-64K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY AND TELETEXT DATA SLICER |
| ST92195B1B1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32-64K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY AND TELETEXT DATA SLICER |
| ST92195B1T1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:32-64K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY AND TELETEXT DATA SLICER |
發布緊急采購，3分鐘左右您將得到回復。