- 您現在的位置：買賣IC網 > PDF目錄98078 > SC28L92A1B-S (NXP SEMICONDUCTORS) 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | SC28L92A1B-S |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQFP44 |
| 封裝： | 10 X 10 MM, 1.75 MM HEIGHT, PLASTIC, SOT-307-2, QFP-44 |
| 文件頁數： | 14/73頁 |
| 文件大?。?/td> | 336K |
| 代理商： | SC28L92A1B-S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
SC28L92_7
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 — 19 December 2007
21 of 73
NXP Semiconductors
SC28L92
3.3 V/5.0 V Dual Universal Asynchronous Receiver/Transmitter
A receiver reset will discard the present shift register date, reset the receiver ready bit
(RxRDY), clear the status of the byte at the top of the FIFO and realign the FIFO
read/write pointers.
6.3.7 Watchdog
A watchdog timer is associated with each receiver. Its interrupt is enabled by MR0[7]. The
purpose of this timer is to alert the control processor that characters are in the Rx FIFO
which have not been read. This situation may occur at the end of a transmission when the
last few characters received are not sufcient to cause an interrupt.
This counter times out after 64 bit times. It is reset each time a character is transferred
from the receiver shift register to the Rx FIFO or a read of the Rx FIFO is executed.
6.3.8 Receiver time-out mode
In addition to the watchdog timer described in Section 6.3.7, the counter/timer may be
used for a similar function. Its programmability, of course, allows much greater precision of
time-out intervals.
The time-out mode uses the received data stream to control the counter. Each time a
received character is transferred from the shift register to the Rx FIFO, the counter is
restarted. If a new character is not received before the counter reaches zero count, the
counter ready bit is set, and an interrupt can be generated. This mode can be used to
indicate when data has been left in the Rx FIFO for more than the programmed time limit.
Otherwise, if the receiver has been programmed to interrupt the CPU when the receive
FIFO is full, and the message ends before the FIFO is full, the CPU may not know there is
data left in the FIFO. The CTU and CTL value would be programmed for just over one
character time, so that the CPU would be interrupted as soon as it has stopped receiving
continuous data. This mode can also be used to indicate when the serial line has been
marking for longer than the programmed time limit. In this case, the CPU has read all of
the characters from the FIFO, but the last character received has started the count. If
there is no new data during the programmed time interval, the counter ready bit will get
set, and an interrupt can be generated.
The time-out mode is enabled by writing the appropriate command to the command
register. Writing 0xA to CRA or CRB will invoke the time-out mode for that channel.
Writing 0xC to CRA or CRB will disable the time-out mode. The time-out mode should
only be used by one channel at once, since it uses the C/T. If, however, the time-out mode
is enabled from both receivers, the time-out will occur only when both receivers have
stopped receiving data for the time-out period. CTU and CTL must be loaded with a value
greater than the normal receive character period. The time-out mode disables the regular
start counter or stop counter commands and puts the C/T into counter mode under the
control of the received data stream. Each time a received character is transferred from the
shift register to the Rx FIFO, the C/T is stopped after one C/T clock, reloaded with the
value in CTU and CTL and then restarted on the next C/T clock. If the C/T is allowed to
end the count before a new character has been received, the counter ready bit, ISR[3], will
be set. If IMR[3] is set, this will generate an interrupt. Receiving a character after the C/T
has timed out will clear the counter ready bit, ISR[3], and the interrupt. Invoking the set
time-out mode on command, CRx = 0xA, will also clear the counter ready bit and stop the
counter until the next character is received.
相關PDF資料 |
PDF描述 |
|---|---|
| SC3327S | LVTTL SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 |
| SC3526S/TD | TTL SERIES, LOW SKEW CLOCK DRIVER, 9 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 |
| SC3527S/D | TTL SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 |
| SC3529S/TD | TTL SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 |
| SC68C198A1A-T | 8 CHANNEL(S), 500K bps, SERIAL COMM CONTROLLER, PQCC84 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC28L92A1BS,528 | 功能描述:UART 接口集成電路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L92A1BS,551 | 功能描述:UART 接口集成電路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L92A1BS,557 | 功能描述:UART 接口集成電路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L92A1BS-F | 功能描述:UART 接口集成電路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L92A1BS-S | 功能描述:UART 接口集成電路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。