- 您現在的位置：買賣IC網 > PDF目錄382377 > PCA5007H (NXP Semiconductors N.V.) Pager baseband controller PDF資料下載
參數資料
| 型號： | PCA5007H |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Pager baseband controller |
| 中文描述： | 傳呼機基帶控制器 |
| 文件頁數： | 94/112頁 |
| 文件大?。?/td> | 604K |
| 代理商： | PCA5007H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁當前第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
1998 Oct 07
94
Philips Semiconductors
Product specification
Pager baseband controller
PCA5007
14 APPENDIX 1: SPECIAL MODES OF THE PCA5007
14.1
Overview
During the rising edge of the external RESOUT signal, the
state of pins ALE, PSEN and EA and P2.X is sampled and
stored. The following decoding (ALE, PSEN and P2) is
used to force the PCA5007 into different operating modes:
[1, 1, X]
→
RUN mode
[0, 1, X]
→
EMUlation modes (for P2 decoding refer to
Metalink documents)
[1, 0, Y]
→
test mode, submode Y
[0, 0, X]
≥
OTP parallel programming mode.
The customer will usually only see the normal RUN mode.
14.2
OTP parallel programming mode
The OTP parallel programming mode is used to access the
on-chip OTP directly from the device pins for programming
and verification. The OTP parallel programming mode and
its initialization are explained in detail in Chapter 15.
14.3
Test modes
The test modes of the PCA5007 are used during the
production test of the circuit. Test modes are not intended
to be used by customers except test mode 2, the
demodulator and clock recovery test mode.
Test mode 2 may be used by customers for Bit Error Rate
(BER) measurements in closed-loop systems.
The following application diagram (see Fig.59) shows an
application, which enters this mode during start-up. After
the test mode is entered the PCA5007 starts execution of
code from the internal program memory. This code must
enable the demodulator and clock recovery in the required
modes. If the microcontroller is requested to make
port I/O, then a frequency of approximately 6 MHz with
V
DD
level needs to be supplied at the TCLK pin.
相關PDF資料 |
PDF描述 |
|---|---|
| PCA5010 | Pager baseband controller |
| PCA5010H | Pager baseband controller |
| PCA82C200 | STAND-ALONE CAN-CONTROLLER |
| PCA82C200P | STAND-ALONE CAN-CONTROLLER |
| PCA82C200T | STAND-ALONE CAN-CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA5007H/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| PCA5010 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5010H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5010H/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|48PIN|PLASTIC |
| PCA503HL320 | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:ZIF FLEX CIRCUIT CONNECTOR |
發布緊急采購，3分鐘左右您將得到回復。