- 您現在的位置：買賣IC網 > PDF目錄382377 > PCA5007H (NXP Semiconductors N.V.) Pager baseband controller PDF資料下載
參數資料
| 型號： | PCA5007H |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Pager baseband controller |
| 中文描述： | 傳呼機基帶控制器 |
| 文件頁數： | 37/112頁 |
| 文件大小： | 604K |
| 代理商： | PCA5007H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
1998 Oct 07
37
Philips Semiconductors
Product specification
Pager baseband controller
PCA5007
6.14
Wake-up counter
6.14.1
F
UNCTION
The wake-up counter is intended to be used as a protocol
timer. It can be programmed to wake-up the processor
when the protocol needs an action. Amongst others this
may be:
Switching on the DC/DC converter at time 0
Enabling the receiver at time 1
Enabling the demodulator and clock recovery function
at time 2 before relevant data is expected.
The time to wake-up is defined as a 16-bit value containing
the number of 9600 Hz ticks. The maximum time interval
that can be spawn with one cycle then equals 6.8 s.
The wake-up counter and its reload latch are supplied by
V
BAT
and operate independent of the 2 V supply.
A reset to the microcontroller does not clear the wake-up
counter control flags or the reload latch, but clears the
reload register (see Fig.19).
The counter is implemented as a 16-bit ripple-down
counter. It can be loaded from the wake-up reload latch by
a signal from the processor. When the counter is loaded it
automatically starts if the RUN signal is active. When the
counter reaches zero the wake-up signal becomes active
and may generate an interrupt. The wake-up signal
automatically reloads the counter (modulo N counter).
The counter is stopped when the RUN signal is written to
logic 0. Auto reloading of the counter is also possible,
when the DC/DC converter is not operating (i.e. V
DD
is
below 1.8 V).
The contents of the wake-up counter cannot be read by the
processor. Reading WUC0 and WUC1 reflects the
contents of the 16-bit wake-up register (set by the
microcontroller).
The interface between the 2 and 1 V regions is
implemented similar to the clock correction block.
The sequence for writing values is identical (see Fig.14).
Fig.19 Block diagram of the wake-up counter.
handbook, full pagewidth
MGR122
Q
D
Q
R
D
1
STORE
9600 Hz
internal
SET FLAG
SFR to
microcontroller
RESET
with each
OFF cycle
SET
CPL
RUN
LOAD
WUP
TEST
Z1
Z0
WU0 to WU15
WU RELOAD LATCH
(16-BIT)
reload data
WU COUNTER
(16-BIT)
&
Interrupt
≥
1
≥
1
reload
VDD supply
wake-up DC/DC converter
VBAT supply
CARRY
RESET only
on RESETIN
相關PDF資料 |
PDF描述 |
|---|---|
| PCA5010 | Pager baseband controller |
| PCA5010H | Pager baseband controller |
| PCA82C200 | STAND-ALONE CAN-CONTROLLER |
| PCA82C200P | STAND-ALONE CAN-CONTROLLER |
| PCA82C200T | STAND-ALONE CAN-CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA5007H/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| PCA5010 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5010H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5010H/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|48PIN|PLASTIC |
| PCA503HL320 | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:ZIF FLEX CIRCUIT CONNECTOR |
發布緊急采購，3分鐘左右您將得到回復。