參數資料
型號: OR4E10
廠商: Lineage Power
英文描述: Field-Programmable Gate Arrays(現場可編程門陣列)
中文描述: 現場可編程門陣列(現場可編程門陣列)
文件頁數: 42/132頁
文件大小: 2667K
代理商: OR4E10
42
Lucent Technologies Inc.
Preliminary Data Sheet
August 2000
ORCA Series 4 FPGAs
Special Function Blocks
(continued)
ORCABoundary-Scan Circuitry
The ORCA Series boundary-scan circuitry includes a
test access port controller (TAPC), instruction register
(IR), boundary-scan register (BSR), and bypass regis-
ter. It also includes circuitry to support the 18 pre-
defined instructions.
Figure 27 shows a functional diagram of the boundary-
scan circuitry that is implemented in the ORCA Series.
The input pins’ (TMS, TCK, and TDI) locations vary
depending on the part, and the output pin is the dedi-
cated TDO/RD_DATA output pad. Test data in (TDI) is
the serial input data. Test mode select (TMS) controls
the boundary-scan test access port controller (TAPC).
Test clock (TCK) is the test clock on the board.
The BSR is a series connection of boundary-scan cells
(BSCs) around the periphery of the IC. Each I/O pad on
the FPGA, except for CCLK, DONE, and the boundary-
scan pins (TCK, TDI, TMS, and TDO), is included in
the BSR. The first BSC in the BSR (connected to TDI)
is located in the first PIO I/O pad on the left of the top
side of the FPGA (PTA PIO). The BSR proceeds clock-
wise around the top, right, bottom, and left sides of the
array. The last BSC in the BSR (connected to TDO) is
located on the top of the left side of the array (PL1D).
The bypass instruction uses a single FF, which resyn-
chronizes test data that is not part of the current scan
operation. In a bypass instruction, test data received on
TDI is shifted out of the bypass register to TDO. Since
the BSR (which requires a two FF delay for each pad)
is bypassed, test throughput is increased when devices
that are not part of a test operation are bypassed.
The boundary-scan logic is enabled before and during
configuration. After configuration, a configuration
option determines whether or not boundary-scan logic
is used.
The 32-bit boundary-scan identification register con-
tains the manufacturer’s ID number, unique part num-
ber, and version (as described earlier). The
identification register is the default source for data on
TDO after RESET if the TAP controller selects the shift-
data-register (SHIFT-DR) instruction. If boundary scan
is not used, TMS, TDI, and TCK become user I/Os, and
TDO is 3-stated or used in the readback operation.
An optional USERCODE is available. The USERCODE
is a 32-bit value that the user can set during device
configuration and can be written to and read from the
FPGA via the boundary-scan logic.
相關PDF資料
PDF描述
OR4E14 Field-Programmable Gate Arrays(現場可編程門陣列)
OR4E2 Field-Programmable Gate Arrays(現場可編程門陣列)
OR4E4 Field-Programmable Gate Arrays(現場可編程門陣列)
OR4E6 Field-Programmable Gate Arrays(現場可編程門陣列)
ORT4622 Field-Programmable System Chip (FPSC) Four Channel x 622 Mbits/s Backplane Transceiver(現場可編程系統芯片(四通道x 622 M位/秒背板收發器))
相關代理商/技術參數
參數描述
OR4E14 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Gate Arrays
OR4E2 制造商:AGERE 制造商全稱:AGERE 功能描述:Field-Programmable Gate Arrays
OR4E2-1BA256 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FPGA
OR4E2-1BA352 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FPGA
OR4E2-1BA416 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FPGA