參數資料
型號： KAB01D100M-TNGP
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： CONNECTOR ACCESSORY
中文描述： 連接器附件
文件頁數： 30/72頁
文件大?。?/td> 1378K
代理商： KAB01D100M-TNGP
KAB0xD100M - TxGP
Revision 1.11
August 2003
- 30 -
MCP MEMORY
SEC Only
R/B
R
: Ready/Busy
The NOR Flash memory has a Ready / Busy output that indicates either the completion of an operation or the status of Internal Algo-
rithms. If the output is Low, the device is busy with either a program or an erase operation. If the output is High, the device is ready to
accept any read/write or erase operation. When the R/B
R
pin is low, the device will not accept any additional program or erase com-
mands with the exception of the Erase Suspend command. If the NOR Flash memory is placed in an Erase Suspend mode, the R/B
R
output will be High. For programming, the RY/ BY is valid (R/B
R
= 0) after the rising edge of the fourth WE pulse in the four write
pulse sequence. For Chip Erase, R/B
R
is also valid after the rising edge of WE pulse in the six write pulse sequence. For Block
Erase, R/B
R
is also valid after the rising edge of the sixth WE pulse.
The pin is an open drain output, allowing two or more Ready/ Busy outputs to be OR-tied. An appropriate pull-up resistor is required
for proper operation.
DQ3 : Block Erase Timer
The status of the multi-block erase operation can be detected via the DQ3 pin. DQ3 will go High if 50
μ
s of the block erase time win-
dow expires. In this case, the Internal Erase Routine will initiate the erase operation.Therefore, the device will not accept further write
commands until the erase operation is completed. DQ3 is Low if the block erase time window is not expired. Within the block erase
time window, an additional block erase command (30H) can be accepted. To confirm that the block erase command has been
accepted, the software may check the status of DQ3 following each block erase command.
DQ2 : Toggle Bit 2
The device generates a toggling pulse in DQ2 only if an Internal Erase Routine or an Erase Suspend is in progress. When the device
executes the Internal Erase Routine, DQ2 toggles only if an erasing block is read. Although the Internal Erase Routine is in the
Exceeded Time Limits, DQ2 toggles only if an erasing block in the Exceeded Time Limits is read. When the device is in the Erase
Suspend mode, DQ2 toggles only if an address in the erasing block is read. If a non-erasing block address is read during the Erase
Suspend mode, then DQ2 will produce valid data. DQ2 will go High if the user tries to program a non-erase suspend block while the
device is in the Erase Suspend mode. Combination of the status in DQ6 and DQ2 can be used to distinguish the erase operation
from the program operation.
Rp
=
Vcc
Ready / Busy
open drain output
Device
Vss
Vcc (Max.) - V
OL
(Max.)
I
OL
+
Σ
I
L
=
2.7 V
2.1mA +
Σ
I
L
where
Σ
I
L
is the sum of the input currents of all devices tied to the
Ready / Busy pin.
Rp
相關PDF資料
PDF描述
KAB02D100M-TNGP CONNECTOR ACCESSORY
KAB3403DN White LED Step-Up Converter
KAB3403T White LED Step-Up Converter
KAB3405T Step Up Type DC/DC Converter for White LED
KAC-749S 4-Channel power amplifier
相關代理商/技術參數
參數描述
KAB02D100M-TLGP 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:Multi-Chip Package MEMORY
KAB02D100M-TNGP 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:Multi-Chip Package MEMORY
KAB03D100M-TLGP 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:Multi-Chip Package MEMORY
KAB03D100M-TNGP 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:Multi-Chip Package MEMORY
KAB04D100M-TLGP 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:Multi-Chip Package MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*