- 您現在的位置：買賣IC網 > PDF目錄384325 > GF9330-CBP (Gennum Corporation) High Performance HDTV/SDTV Deinterlacer PDF資料下載
參數資料
| 型號： | GF9330-CBP |
| 廠商： | Gennum Corporation |
| 英文描述： | High Performance HDTV/SDTV Deinterlacer |
| 中文描述： | 高性能高清/標清去隔行掃描 |
| 文件頁數： | 31/42頁 |
| 文件大?。?/td> | 449K |
| 代理商： | GF9330-CBP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
GF9330 Data Sheet
31 of 42
Proprietary and Confidential
18283 - 4
June 2004
3.8 RESET
The RESET pin will reset all internal logic to it's default conditions when set LOW.
On power up it is recommended to reset the device to ensure all internal registers
are set to their default state. When applying a reset, the GF9330 will load in the
STD[4:0] and MODE[2:0] settings from the external pins. If no further configuration
is done, these settings will be used for the operation of the device.
3.9 Modes of Operation
The GF9330 supports stand-alone, co-processor enabled, pass-through and film
rate down conversion modes of operation.
Table 3-6: Modes of Operation:
MODE[2:0]
shows the basic operating modes for the GF9330 as selected using the
MODE[2:0] control bits or through the host interface using the MODE[2:0] register,
Address [0][7:5].
3.9.1 De-Interlacing Mode (MODE=000)
When set to operate as a de-interlacer the GF9330 can operate as a “stand-alone”
device performing motion adaptive processing. To enable multi-directional edge
and vertical motion detection the GF9330 must be connected to the GF9331 as
described in
3.3 Seamless Interface to the GF9331 Motion Co-processor for
Directional Filter Control
.
Segmented frame to progressive frame conversion is also supported in this mode.
This function is performed when the progressive segmented frame input video
format is selected on either the external pins or host interface register STD[4:0].
3.9.2 De-interlacing Mode with Pull-down Compensation (MODE=001)
When set to operate in this mode, the GF9330 can operate as a “stand-alone”
device performing motion adaptive processing with added 3:2 pull-down
compensation. To enable multi-directional edge and vertical motion detection the
GF9330 must be connected to the GF9331 as described in
3.3 Seamless Interface
to the GF9331 Motion Co-processor for Directional Filter Control
.
Table 3-6: Modes of Operation: MODE[2:0]
Mode
Description
000
Motion adaptive de-interlacing of input video signal.
001
De-interlacing of input video signal with pull-down compensation.
010
Film rate down conversion mode (60Hz -> 24Hz).
011
Film rate down conversion mode (60Hz -> 24Hz Segmented Frame)
100 to 110
Reserved
111
Video pass through mode.
相關PDF資料 |
PDF描述 |
|---|---|
| GF9331-CBP | DTV/SDTV Motion Co-processor |
| GFMM | Ceramic Capacitors Stacks |
| GFMM2505 | Ceramic Capacitors Stacks |
| GFMM2507 | Ceramic Capacitors Stacks |
| GH06510B2A | RED LASER DIODE FOR DVD ROM DRIVE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GF9331 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GF9331 - HDTV/SDTV Motion Co-processor |
| GF9331-CBP | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:DTV/SDTV Motion Co-processor |
| GF9351A-CBE2 | 制造商:Sigma Designs 功能描述:IC IMAGE PROCESSOR 10BIT DUAL |
| GF9410\5B | 功能描述:MOSFET N-Channel 30V 2A RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| GF9450C-CBE3 | 制造商:Sigma Designs 功能描述:IC VIDEO PROCESSOR 10BIT 701HSBG |
發布緊急采購，3分鐘左右您將得到回復。