- 您現在的位置：買賣IC網 > PDF目錄379876 > celeron cpu Mobile Module (Intel Corp.) processor Mobile Module Connector 1 (MMC-1) at 466 MHz and 433MHZ(工作頻率466和433兆赫茲帶連接器1處理器) PDF資料下載
參數資料
| 型號： | celeron cpu Mobile Module |
| 廠商： | Intel Corp. |
| 英文描述： | processor Mobile Module Connector 1 (MMC-1) at 466 MHz and 433MHZ(工作頻率466和433兆赫茲帶連接器1處理器) |
| 中文描述： | 移動處理器模塊連接器1（MMC管理- 1）在466 MHz和433MHz的（工作頻率466和433兆赫茲帶連接器1處理器） |
| 文件頁數： | 35/42頁 |
| 文件大?。?/td> | 448K |
| 代理商： | CELERON CPU MOBILE MODULE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
31
Celeron
Processor Mobile Module MMC-1
at 466 MHz and 433 MHz
4.9
Thermal Sensor Configuration Register
The configuration register of the thermal sensor controls the
operating mode (Auto Convert vs. Standby) of the device.
Since the processor temperature varies dynamically during
normal operation, Auto Convert mode should be used
exclusively to monitor processor temperature. Table 23
shows the format of the configuration register. If the
RUN/STOP bit is low, then the thermal sensor enters auto-
conversion mode. If the RUN/STOP bit is set high, then the
thermal sensor immediately stops converting and enters
Standby mode. The thermal sensor will still perform
temperature conversions in Standby mode when it receives
a one-shot command. However, the result of a one-shot
command during Auto Convert mode is not guaranteed. Intel
does not recommend using the one-shot command to
monitor temperature when the processor is active, only Auto
Convert mode should be used. Refer to the
Mobile Pentium
II Processor and Pentium
II Processor Mobile Module
Thermal Sensor Interface Specifications
.
Table 23. Thermal Sensor Configuration Register
Reset State
Bit
Name
Function
7 MSB
MASK
0
Masks SMBALERT# when high.
6
RUN/STOP
0
Standby mode control bit. If low, the device enters Auto Convert mode. If high, the
device immediately stops converting, and enters standby mode where the one-
shot command can be performed.
5-0
RFU
0
Reserved for future use.
NOTE:
All RFU bits should be written as “0” and read as “don’t care” for programming purposes.
5.0
MECHANICAL SPECIFICATION
This section provides the physical dimensions for the
Celeron processor mobile module MMC-1.
5.1
Module Dimensions
Figure 10 shows the board dimensions and the orientation
for the Celeron processor mobile module MMC-1.
Figure 10. Celeron Processor Mobile Module MMC-1 Board Dimensions
相關PDF資料 |
PDF描述 |
|---|---|
| celeron CPU with Mobile Module | processor Mobile Module Connector 2 (MMC-2) at 466 MHz and 433MHZ(工作頻率466和433兆赫茲帶連接器2處理器) |
| Celeron Processor with mobile | Celeron Processor Mobile Module MMC-1 at 400 MHz, 366 MHz, 333 MHz, and 300 MHz(工作頻率400,366,333,300和266兆赫茲帶移動模塊和連接器1處理器) |
| celeron processor | 32 bit Celeron Processor Mobile Module(32 位帶移動模塊處理器) |
| CEM11C2 | Dual Enhancement Mode Field Effect Transistor (N and P Channel) |
| CEM2005 | Dual Enhancement Mode Field Effect Transistor(N and Channel) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CELF001001J1 | 制造商:Panasonic Industrial Company 功能描述:FILTER |
| CELHK11-1REC5-59-3.00-AV-01-V | 功能描述:CIRCUIT BRKR MAG-HYDR LEVER 3A 制造商:sensata technologies/airpax 系列:CEL 零件狀態:有效 斷路器類型:磁性（液力延遲） 額定電流:3A 額定電壓 - AC:- 額定電壓 - DC:- 極數:2 致動器類型:搖臂 照明:- 照明電壓（標稱值）:- 安裝類型:面板安裝 標準包裝:1 |
| CELHK11-1REC5-59-35.0-AV-01-V | 功能描述:CIRCUIT BRKR MAG-HYDR LEVER 35A 制造商:sensata technologies/airpax 系列:CEL 零件狀態:有效 斷路器類型:磁性（液力延遲） 額定電流:35A 額定電壓 - AC:- 額定電壓 - DC:- 極數:2 致動器類型:搖臂 照明:- 照明電壓（標稱值）:- 安裝類型:面板安裝 標準包裝:1 |
| CELHK11-1REC5-71165-10-V | 功能描述:CIRCUIT BREAKER MAG-HYDR LEVER 制造商:sensata technologies/airpax 系列:* 零件狀態:有效 標準包裝:1 |
| CELHK11-1REC5-71165-11-V | 功能描述:CIRCUIT BREAKER MAG-HYDR LEVER 制造商:sensata technologies/airpax 系列:* 零件狀態:有效 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。