參數資料
型號： AD9974BBCZRL
廠商： Analog Devices Inc
文件頁數： 33/52頁
文件大?。?/td> 0K
描述： IC CCDSP DUAL 14BIT 100-CSPBGA
標準包裝： 1
類型： CCD 信號處理器，14 位
輸入類型： 邏輯
輸出類型： 邏輯
接口： 3 線串口
電流 - 電源： 55mA
安裝類型： 表面貼裝
封裝/外殼： 100-LFBGA，CSPBGA
供應商設備封裝： 100-CSBGA（9x9）
包裝： 標準包裝
其它名稱： AD9974BBCZRLDKR
AD9974
Rev. A | Page 39 of 52
3-WIRE SERIAL INTERFACE TIMING
All of the internal registers of the AD9974 are accessed through
a 3-wire serial interface. Each register consists of a 12-bit address
and a 28-bit data-word. Both the 12-bit address and 28-bit data-
word are written starting with the LSB. To write to each register,
a 40-bit operation is required, as shown in Figure 52. Although
many registers are fewer than 28 bits wide, all 28 bits must be
written for each register. For example, if the register is only 20 bits
wide, the upper eight bits are don’t cares and must be filled with
0s during the serial write operation. If fewer than 28 data bits
are written, the register is not updated with new data.
Figure 53 shows a more efficient way to write to the registers,
using the AD9974 address auto-increment capability. Using this
method, the lowest desired address is written first, followed by
multiple 28-bit data-words. Each new 28-bit data-word is
automatically written to the next highest register address. By
eliminating the need to write each 12-bit address, faster register
loading is achieved. Continuous write operations can be used,
starting with any register location.
A4
A5
A2
A3
SDATA
A0A1
A6
A8A9
A10
A11
D0
D1
D2
D3
D25
D26
D27
SL
A7
tLS
tDS
12-BIT ADDRESS
28-BIT DATA
5
40
6
7
8
9
10
11
1213141516
38
39
tLH
tDH
NOTES
1. SDATA BITS ARE LATCHED ON SCK RISING EDGES. SCK CAN IDLE HIGH OR LOW BETWEEN WRITE OPERATIONS.
2. ALL 40 BITS MUST BE WRITTEN: 12 BITS FOR ADDRESS AND 28 BITS FOR DATA.
3. IF THE REGISTER LENGTH IS <28 BITS, THEN ZEROS MUST BE USED TO COMPLETE THE 28-BIT DATA LENGTH.
4. NEW DATA VALUES ARE UPDATED IN THE SPECIFIED REGISTER LOCATION AT DIFFERENT TIMES, DEPENDING ON THE
PARTICULAR REGISTER WRITTEN TO. SEE THE UPDATING OF NEW REGISTER VALUES SECTION FOR MORE INFORMATION.
SCK
12
34
05
95
5-
05
2
Figure 52. Serial Write Operation
SDATA
A0A1
A2
A10
A11
D0D1
D26
D27
SCK
SL
A3
NOTES
1. MULTIPLE SEQUENTIAL REGISTERS CAN BE LOADED CONTINUOUSLY.
2. THE FIRST (LOWEST ADDRESS) REGISTER ADDRESS IS WRITTEN, FOLLOWED BY MULTIPLE 28-BIT DATA-WORDS.
3. THE ADDRESS AUTOMATICALLY INCREMENTS WITH EACH 28-BIT DATA-WORD (ALL 28 BITS MUST BE WRITTEN).
4. SL IS HELD LOW UNTIL THE LAST DESIRED REGISTER HAS BEEN LOADED.
D0
D1
D26
D27
D0
DATA FOR STARTING
REGISTER ADDRESS
DATA FOR NEXT
REGISTER ADDRESS
D2
D1
1
40
2
3
4
11
121314
39
42
41
68
67
70
69
71
0
59
55
-0
53
Figure 53. Continuous Serial Write Operation
相關PDF資料
PDF描述
AD9979BCPZRL IC PROCESSOR CCD 14BIT 48-LFCSP
AD9980KSTZ-95 IC INTERFACE 8BIT ANALOG 80LQFP
AD9981KSTZ-95 IC INTERFACE 10BIT ANALOG 80LQFP
AD9983AKSTZ-170 IC DISPLAY 8BIT 170MSPS 80LQFP
AD9985KSTZ-140 IC INTERFACE 8BIT 140MSPS 80LQFP
相關代理商/技術參數
參數描述
AD9975 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End
AD9975ABST 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End
AD9975ABSTEB 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End
AD9975ABSTRL 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End
AD9975BST 制造商:Analog Devices 功能描述:Mixed Signal Front End 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:10 BIT ANALOG FRONT END WITH HALF DUPLEX - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*