參數資料
型號： W28J320TT90L
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 2M X 16 FLASH 2.7V PROM, 90 ns, PDSO48
封裝： 12 X 20 MM, TSOP-48
文件頁數： 3/48頁
文件大?。?/td> 1513K
代理商： W28J320TT90L
W28J320B/T
Publication Release Date: April 11, 2003
- 11 -
Revision A4
8. BUS OPERATION
The local CPU reads and writes flash memory in-system. All bus cycles to or from the flash memory
conform to standard microprocessor bus cycles.
Read
Information can be read from any block, identifier codes or status register independent of the VPP
voltage. #RESET can be at VIH.
The first task is to write the appropriate read mode command (Read Array, Read Identifier Codes or
Read Status Register) to the CUI. Upon initial device power-up or after exit from reset mode, the
device automatically resets to read array mode. Six control pins dictate the data flow in and out of the
component: #CE, #OE, #BYTE, #WE, #RESET and #WP. #CE and #OE must be driven active to
obtain data at the outputs. #CE is the device selection control, and when active enables the selected
memory device. #OE is the data output (DQ0
DQ15) control and when active drives the selected
memory data onto the I/O bus. #BYTE is the device I/O interface mode control. #WE must be at VIH,
#RESET must be at VIH, and #BYTE and #WP must be at VIL or VIH. Figure 16, 17 illustrates read
cycle.
Output Disable
With #OE at a logic-high level (VIH), the device outputs are disabled. Output pins (DQ0 DQ15) are
placed in a high-impedance state.
Standby
Setting #CE to a logic-high level (VIH) deselects the device and places it in standby mode, which
substantially reduces device power consumption. DQ0
DQ15 outputs are placed in a high
impedance state independent of #OE. If deselected during block erase, full chip erase, word/byte write
or lock-bit configuration, the device continues functioning, and it continues to consume active power
until the operation is completed.
Reset
Setting #RESET to VIL initiates the reset mode.
In read modes, setting #RESET at VIL deselects the memory, places output drivers in a high-
impedance state and turns off all internal circuits. #RESET must be held low for a minimum of 100ns.
A delay (tPHQV) is required after return from reset until initial memory access outputs are valid. After
this wake-up interval, normal operation is restored. The CUI is reset to read array mode status register
is set to 80H, and all blocks are locked.
During block erase, full chip erase, word/byte write or lock-bit configuration modes, #RESET at VIL will
abort the operation. RY/#BY remains low until the reset operation is complete. Memory contents at the
aborted location are no longer valid since the data may be partially erased or written. A delay (tPHWL) is
required after #RESET goes to logic-high (VIH) before another command can be written.
As with any automated device, it is important to assert #RESET during system reset. When the
system comes out of reset, it expects to read from the flash memory. Automated flash memories
provide status information when accessed during block erase, full chip erase, word/byte write or lock-
bit configuration modes. If a CPU reset occurs with no flash memory reset, proper CPU initialization
may not occur because the flash memory may be providing status information instead of array data.
Winbond's flash memory solutions allow proper CPU initialization following a system reset through the
use of the #RESET input. In this application, #RESET is controlled by the same #RESET signal that
resets the system CPU.
相關PDF資料
PDF描述
W29S201T-45 128K X 16 FLASH 5V PROM, 15 ns, PDSO48
W301 PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 28VDC, PANEL MOUNT-THREADED
W31-X2M5G-5 TOGGLE SWITCH, SPST, LATCHED, 5A, 50VDC, PANEL MOUNT
W321-0PB-014B T-3 1/4 SINGLE COLOR LED, SUPER BLUE, 9 mm
W321-0UG-048B T-3 1/4 SINGLE COLOR LED, LIME GREEN, 9 mm
相關代理商/技術參數
參數描述
W28NK60Z 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:N-CHANNEL 600 V - 0.155з - 27A TO-247 Zener-Protected SuperMESH MOSFET
W28-SQ11A-10 功能描述:CIRCUIT BREAK 10A W/SWITCH RoHS:否 類別:過電壓，電流，溫度裝置 >> 斷路器 系列:W28 標準包裝:3 系列:AS168X 斷路器類型:熱磁動式 電壓:65VDC，277/480VAC 電流 - 跳閘(It):30A 極數:3 觸動器類型:按片 安裝類型:DIN 軌道 其它名稱:4420.02104420.0210-ND486-2338AS168X-CB3G300-NDCBE AS168X-CB3G300
W28-SQ11A-15 制造商:TE Connectivity 功能描述:
W28-SQ11A-3 制造商:TE Connectivity 功能描述:Circuit Breaker Thermal 1Pole 3A 250VAC/32VDC
W28-SQ11A-5 制造商:TE Connectivity 功能描述:Circuit Breaker Thermal 1Pole 5A 250VAC/32VDC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*