參數資料
型號： W25Q64BVSSIG
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 8M X 8 SPI BUS SERIAL EEPROM, PDSO8
封裝： 0.208 INCH, GREEN, PLASTIC, SOIC-8
文件頁數： 37/61頁
文件大?。?/td> 1726K
代理商： W25Q64BVSSIG
W25Q64BV
- 42 -
11.2.24 High Performance Mode (A3h)
The High Performance Mode (HPM) instruction must be executed prior to Dual or Quad I/O instructions
when operating at high frequencies (see FR and FR1 in AC Electrical Characteristics). This instruction
allows pre-charging of internal charge pumps so the voltages required for accessing the Flash memory
array are readily available. The instruction sequence includes the A3h instruction code followed by three
dummy byte clocks shown in Fig. 24. After the HPM instruction is executed, the device will maintain a
slightly higher standby current (Icc3) than standard SPI operation. The Release from Power-down or
HPM instruction (ABh) can be used to return to standard SPI standby current (Icc1). In addition, Write
Enable instruction (06h) and Power Down instruction (B9h) will also release the device from HPM mode
back to standard SPI standby state.
Figure 24. High Performance Mode Instruction Sequence
11.2.25 Release Power-down or High Performance Mode / Device ID (ABh)
The Release from Power-down or High performance Mode / Device ID instruction is a multi-purpose
instruction. It can be used to release the device from the power-down state or High Performance Mode,
or obtain the devices electronic identification (ID) number.
To release the device from the power-down state or High Performance Mode, the instruction is issued by
driving the /CS pin low, shifting the instruction code “ABh” and driving /CS high as shown in figure 25.
Release from power-down will take the time duration of tRES1 (See AC Characteristics) before the device
will resume normal operation and other instructions are accepted. The /CS pin must remain high during
the tRES1 time duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by
driving the /CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The Device ID
bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in figure
26. The Device ID values for the W25Q64BV is listed in Manufacturer and Device Identification table. The
Device ID can be read continuously. The instruction is completed by driving /CS high.
相關PDF資料
PDF描述
WE128K8-250CCA EEPROM 5V MODULE, CDIP32
W25Q16CVTCAG 16M X 1 SPI BUS SERIAL EEPROM, PBGA24
WF2M32S-100HM 8M X 8 FLASH 5V PROM MODULE, 100 ns, CHIP66
WF2M32S-100HC 8M X 8 FLASH 5V PROM MODULE, 100 ns, CHIP66
WF2M32S-120GTC 8M X 8 FLASH 5V PROM MODULE, 120 ns, CQFP68
相關代理商/技術參數
參數描述
W25Q64BVSSIGTR 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 64M-BIT, 4KB UNIFORM
W25Q64BVSSIP 制造商:WINBOND 制造商全稱:Winbond 功能描述:64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q64BVZEIG 功能描述:IC SPI FLASH 64MBIT 8WSON RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-MFP 包裝:帶卷 (TR)
W25Q64BVZEIP 制造商:WINBOND 制造商全稱:Winbond 功能描述:64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q64CV 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*