參數資料
型號: TCM4400EGGM
廠商: Texas Instruments, Inc.
英文描述: GSM/DCS BASEBAND AND VOICE A/D AND D/A RF INTERFACE CIRCUIT
中文描述: 的GSM / DCS的基帶和語音的A / D和D / A射頻接口電路
文件頁數: 49/64頁
文件大?。?/td> 888K
代理商: TCM4400EGGM
TCM4400E
GSM/DCS BASEBAND AND VOICE A/D
AND D/A RF INTERFACE CIRCUIT
SLWS082A – JULY 1999 – REVISED MARCH 2000
49
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
power down register No. 1
The values in each bit position of power down register No. 1 have the meaning outlined in Table 14.
ááááááááááááááááááááááááááááááá
ááááááááááááááááááááááááááá
ááááááááááááá
BBRST:
This is the digital reset of the baseband codec (active at 1); the uplink burst buffer is loaded with
all 1s and the memory and registers of the downlink digital filter is cleared to 0. This is not a
toggle bit as it has to be set to 0 to remove the reset condition.
PWDNRG1: REGISTER FOR POWERING DOWN
ADDRESS: 7
R/W
ááááááááááááááááá
ááááááááááááááááááááááááááá
áááááááááááááááááááááááááááá
EXTCAL:
Downlink autocalibration mode (at 0: autocalibration; at 1: external calibration)
BBULW:
If cleared to 0, the baseband uplink path is powered down under the control of the GSM transmit
window (BULON terminal). If this bit is set to 1, the power down is only controlled by bit
BBULPD.
BBULPD:
This bit is functionally associated with bit BBULW. When this bit is set to 1, the baseband uplink
path is in power-down mode.
BBDLW:
If cleared to 0, the baseband downlink path is powered down under the control of GSM receive
window (BDLON terminal). If this bit is set to 1, the power down is only controlled by bit
BBDLPD.
BBDLPD:
This bit is functionally associated with bit BBDLW. When this bit is set to 1, the baseband
downlink path is in power-down mode.
VMIDW:
If cleared to 0, the VMID output driver is powered down under the control of GSM transmit
window (BULON terminal). If this bit is set to 1, the power down is only controlled by bit
VMIDPD.
VMIDPD:
This bit is functionally associated and paired with bit VMIDW. When VMIDW bit is set to 1, the
VMID output driver is active. When VMIDPD bit is set to 1, the VMID output driver is in
power-down mode.
BALOOP:
When set to 1, the internal analog loop of I and Q uplink terminals are connected to I and Q
downlink terminals.
SELVMID: When cleared to 0, this sets the common-mode voltage of the baseband uplink and VMID at
V
DD
/2; when set to 1, these voltages are set to 1.35 V.
相關PDF資料
PDF描述
TCM4400ETQFP GSM/DCS BASEBAND AND VOICE A/D AND D/A RF INTERFACE CIRCUIT
tcm5003d 1/4 Inch 330k Pixel Color Image Sensor(1/4英寸330k像素彩色圖象傳感器)
TCM5089 TONE ENCODER
TCM5092 TONE ENCOER
TCM5094 TONE ENCOER
相關代理商/技術參數
參數描述
TCM4400EPET 制造商:Rochester Electronics LLC 功能描述:GSM CELL PHONE INTERFACE CHIP (VEGA) - Tape and Reel
TCM4400EPN 制造商:Rochester Electronics LLC 功能描述:GSM CELL PHONE INTERFACE CHIP (VEGA-E) - Bulk
TCM4400EPNR 制造商:Rochester Electronics LLC 功能描述:- Bulk
TCM4400ETQFP 制造商:TI 制造商全稱:Texas Instruments 功能描述:GSM/DCS BASEBAND AND VOICE A/D AND D/A RF INTERFACE CIRCUIT
TCM46T 制造商:MINICIR 功能描述:New