參數資料
型號： S1C6P466D0A0A00
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, UUC140
封裝： DIE-140
文件頁數： 9/174頁
文件大?。?/td> 1582K
代理商： S1C6P466D0A0A00
96
EPSON
S1C6P466 TECHNICAL MANUAL
CHAPTER 5: PROM PROGRAMMING AND OPERATING MODE
CHAPTER
5 PROM PROGRAMMING AND
OPERATING MODE
The S1C6P466 has built-in Flash EEPROMs as the code PROM and the data PROM that allow the
developer to program the PROM data using the exclusive PROM writer (Universal ROM Writer II
(S5U1C88000W1)). This chapter explains the PROM programmer that controls data writing and the
writing mode.
5.1 Configuration of PROM Programmer
The configuration of the PROM programmer is shown in Figure 5.1.1.
Serial interface
controller
Code
PROM
Programming
control circuit
Parallel interface
controller
VDDF
VSS
RXD
TXD
SCLK
CLKIN
Address
Data
Control signal
SPRG
Data
PROM
PROM programmer
PROM block
From/to
exclusive
PROM writer
Fig. 5.1.1 Configuration of PROM programmer
The PROM programmer supports the following two writing modes.
1) Serial Programming
2) Parallel Programming
Serial programming mode uses the serial communication ports of the PROM writer and S1C6P466 to
write data. This mode enables on-board programming by designing the target board with a serial writing
function. In parallel programming mode, the on-chip PROM can be directly programmed using the
exclusive PROM writer with the adaptor socket installed. Refer to Section 5.2, "Operating Mode", for each
programming method.
Terminals
The S1C6P466 provides the following terminals for programming the Flash EEPROM.
VDDF
Power supply (+) terminal for Flash EEPROM (The VDDF terminal should be connected to VDD.)
SPRG
Flash programming control terminal (pull-up resistor built-in)
When set to High ..... Normal operation mode (The CPU executes the program in the Flash
EEPROM.)
When set to Low ...... Programming mode (for writing data to the Flash EEPROM)
SCLK
Serial transfer clock input/output terminal for Serial Programming (pull-up resistor built-in)
RXD
Serial data input terminal for Serial Programming (pull-up resistor built-in)
TXD
Serial data output terminal for Serial Programming
CLKIN PROM programmer clock input terminal (1 MHz; pull-up resistor built-in)
RSTOUTTest signal monitor terminal (Not used when writing; keep it open)
VEPEXT Test signal monitor terminal (Not used when writing; keep it open)
The eight terminals above are provided exclusively for the Flash EEPROM. The S1C63454, S1C63458
and S1C63466 do not have these terminals.
相關PDF資料
PDF描述
S1C6S2L7D 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58
S1C6S2A7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2B7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2N7D 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC58
S1C6S2N7F0A0100 MICROCONTROLLER, PQFP60
相關代理商/技術參數
參數描述
S1C-6-S 制造商:GRIPCO 功能描述:
S1C7309X 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C7309X01 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C88349 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88649 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*