參數(shù)資料
型號: S1C6P466D0A0A00
元件分類: 微控制器/微處理器
英文描述: MICROCONTROLLER, UUC140
封裝: DIE-140
文件頁數(shù): 145/174頁
文件大小: 1582K
代理商: S1C6P466D0A0A00
62
EPSON
S1C6P466 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Programmable Timer)
Counter
input clock
2
Counter data
n
n-1
n-2
n-3
K13 input
2,048 Hz
1
1 When fOSC1 is 32.768 kHz
2 When PLPOL register is set to "0"
Fig. 4.10.3.2 Count down timing with noise rejecter
The operation of the event counter mode is the same as the timer mode except it uses the K13 input as
the clock.
Refer to Section 4.10.2, "Setting of initial value and counting down" for basic operation and control.
4.10.4 Setting of input clock in timer mode
Timer 0 and timer 1 each include a prescaler. The prescalers generate the input clock for each timer by
dividing the source clock supplied from the OSC1 or OSC3 oscillation circuit.
The source clock (OSC1 or OSC3) and the division ratio of the prescaler can be selected with software for
timer 0 and timer 1 individually.
The set input clock is used for the count clock during operation in the timer mode. When the timer 0 is
used in the event counter mode, the following settings become invalid.
The input clock is set in the following sequence.
(1) Selection of source clock
Select the source clock input to each prescaler from either OSC1 or OSC3. This selection is done using
the source clock selection registers CKSEL0 (timer 0) and CKSEL1 (timer 1); when "0" is written to the
register, OSC1 is selected and when "1" is written, OSC3 is selected.
When the OSC3 oscillation clock is selected for the clock source, it is necessary to turn the OSC3
oscillation ON, prior to using the programmable timer. However the OSC3 oscillation circuit requires
a time at least 5 msec from turning the circuit ON until the oscillation stabilizes. Therefore, allow an
adequate interval from turning the OSC3 oscillation circuit ON to starting the programmable timer.
Refer to Section 4.3, "Oscillation Circuit", for the control and notes of the OSC3 oscillation circuit.
At initial reset, the OSC3 oscillation circuit is set in the OFF state.
(2) Selection of prescaler division ratio
Select the division ratio for each prescaler from among 4 types. This selection is done using the
prescaler division ratio selection registers PTPS00/PTPS01 (timer 0) and PTPS10/PTPS11 (timer 1).
Table 4.10.4.1 shows the correspondence between the setting value and the division ratio.
Table 4.10.4.1 Selection of prescaler division ratio
PTPS11
PTPS01
1
0
PTPS10
PTPS00
1
0
1
0
Prescaler division ratio
Source clock / 256
Source clock / 32
Source clock / 4
Source clock / 1
By writing "1" to the register PTRUN0 (timer 0) or PTRUN1 (timer 1), the prescaler inputs the source
clock and outputs the clock divided by the selected division ratio. The counter starts counting down
by inputting the clock.
相關PDF資料
PDF描述
S1C6S2L7D 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58
S1C6S2A7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2B7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2N7D 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC58
S1C6S2N7F0A0100 MICROCONTROLLER, PQFP60
相關代理商/技術參數(shù)
參數(shù)描述
S1C-6-S 制造商:GRIPCO 功能描述:
S1C7309X 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C7309X01 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C88349 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88649 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer