參數資料
型號： S1C6P466D0A0A00
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, UUC140
封裝： DIE-140
文件頁數： 159/174頁
文件大?。?/td> 1582K
代理商： S1C6P466D0A0A00
S1C6P466 TECHNICAL MANUAL
EPSON
75
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
4.11.5 I/O memory of serial interface
Table 4.11.5.1 shows the I/O addresses and the control bits for the serial interface.
Table 4.11.5.1 Control bits of serial interface
Address
Comment
D3
D2
Register
D1
D0
Name
Init 1
10
FF45H
PUL13
PUL12
PUL11
PUL10
R/W
PUL13
PUL12
PUL11
PUL10
1
On
Off
P13 pull-up control register
functions as a general-purpose register when SIF (slave) is selected
P12 pull-up control register (ESIF=0)
functions as a general-purpose register when SIF (master) is selected
SCLK (I) pull-up control register when SIF (slave) is selected
P11 pull-up control register (ESIF=0)
functions as a general-purpose register when SIF is selected
P10 pull-up control register (ESIF=0)
SIN pull-up control register when SIF is selected
R/W
FF72H
SD3
SD2
SD1
SD0
SD3
SD2
SD1
SD0
– 2
High
Low
MSB
Serial I/F transmit/receive data (low-order 4 bits)
LSB
R/W
FF73H
SD7
SD6
SD5
SD4
SD7
SD6
SD5
SD4
– 2
High
Low
MSB
Serial I/F transmit/receive data (high-order 4 bits)
LSB
FF70H
00
SCTRG
ESIF
R
R/W
0 3
SCTRG
ESIF
– 2
0
Trigger
Run
SIF
Invalid
Stop
I/O
Unused
Serial I/F clock trigger (writing)
Serial I/F clock status (reading)
Serial I/F enable (P1 port function selection)
FFE3H
000
EISIF
R
R/W
0 3
EISIF
– 2
0
Enable
Mask
Unused
Interrupt mask register (Serial I/F)
FFF3H
000
ISIF
R
R/W
0 3
ISIF
– 2
0
(R)
Yes
(W)
Reset
(R)
No
(W)
Invalid
Unused
Interrupt factor flag (Serial I/F)
0
Slave
2
OSC1/2
1
PT
3
OSC1
[SCS1, 0]
Clock
[SCS1, 0]
Clock
FF71H
SDP
SCPS
SCS1
SCS0
R/W
SDP
SCPS
SCS1
SCS0
0
MSB first LSB first Serial I/F data input/output permutation
Serial I/F clock phase selection
Serial I/F
clock mode selection
*1 Initial value at initial reset
*2 Not set in the circuit
*3 Constantly "0" when being read
ESIF: Serial interface enable register (P1 port function selection) (FF70HD0)
Sets P10–P13 to the input/output port for the serial interface.
When "1" is written: Serial interface
When "0" is written: I/O port
Reading: Valid
When "1" is written to the ESIF register, P10, P11, P12 and P13 function as SIN, SOUT, SCLK, SRDY,
respectively.
In the slave mode, the P13 terminal functions as SRDY output terminal, while in the master mode, it
functions as the I/O port terminal.
At initial reset, this register is set to "0".
Note: After setting ESIF to "1", wait at least 10 sec before starting actual data transfer since a hazard
may be generated from the P12 (SCLK) terminal when ESIF is set to "1".
相關PDF資料
PDF描述
S1C6S2L7D 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58
S1C6S2A7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2B7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2N7D 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC58
S1C6S2N7F0A0100 MICROCONTROLLER, PQFP60
相關代理商/技術參數
參數描述
S1C-6-S 制造商:GRIPCO 功能描述:
S1C7309X 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C7309X01 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C88349 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88649 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*