參數資料
型號: S1C6P466D0A0A00
元件分類: 微控制器/微處理器
英文描述: MICROCONTROLLER, UUC140
封裝: DIE-140
文件頁數: 139/174頁
文件大?。?/td> 1582K
代理商: S1C6P466D0A0A00
S1C6P466 TECHNICAL MANUAL
EPSON
57
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Stopwatch Timer)
4.9.4 I/O memory of stopwatch timer
Table 4.9.4.1 shows the I/O addresses and the control bits for the stopwatch timer.
Table 4.9.4.1 Control bits of stopwatch timer
Address
Comment
D3
D2
Register
D1
D0
Name
Init 1
10
W
R/W
R
FF7CH
00
SWRST SWRUN
0 3
SWRST3
SWRUN
2
Reset
0
Reset
Run
Invalid
Stop
Unused
Stopwatch timer reset (writing)
Stopwatch timer Run/Stop
R
FF7DH
SWD3
SWD2
SWD1
SWD0
SWD3
SWD2
SWD1
SWD0
0
Stopwatch timer data
BCD (1/100 sec)
SWD7
SWD6
SWD5
SWD4
0
Stopwatch timer data
BCD (1/10 sec)
R
FF7EH
SWD7
SWD6
SWD5
SWD4
FFE7H
00
EISW1 EISW10
R
R/W
0 3
EISW1
EISW10
2
0
Enable
Mask
Unused
Interrupt mask register (Stopwatch timer 1 Hz)
Interrupt mask register (Stopwatch timer 10 Hz)
FFF7H
00
ISW1
ISW10
R
R/W
0 3
ISW1
ISW10
2
0
(R)
Yes
(W)
Reset
(R)
No
(W)
Invalid
Unused
Interrupt factor flag (Stopwatch timer 1 Hz)
Interrupt factor flag (Stopwatch timer 10 Hz)
*1 Initial value at initial reset
*2 Not set in the circuit
*3 Constantly "0" when being read
SWD0–SWD7: Stopwatch timer data (FF7DH, FF7EH)
The 1/100 sec and the 1/10 sec data (BCD) can be read from SWD0–SWD3 and SWD4–SWD7, respec-
tively. These eight bits are read only, and writing operations are invalid.
At initial reset, the timer data is initialized to "00H".
SWRST: Stopwatch timer reset (FF7CHD1)
When "1" is written: Stopwatch timer reset
When "0" is written: No operation
Reading: Always "0"
The stopwatch timer is reset by writing "1" to SWRST. All timer data is set to "0". When the stopwatch
timer is reset in the RUN status, operation restarts immediately. Also, in the STOP status the reset data is
maintained. No operation results when "0" is written to SWRST.
This bit is write-only, and so is always "0" at reading.
SWRUN: Stopwatch timer RUN/STOP control register (FF7CHD0)
Controls RUN/STOP of the stopwatch timer.
When "1" is written: RUN
When "0" is written: STOP
Reading: Valid
The stopwatch timer enters the RUN status when "1" is written to the SWRUN register, and the STOP
status when "0" is written.
In the STOP status, the timer data is maintained until the next RUN status or the timer is reset. Also,
when the STOP status changes to the RUN status, the data that is maintained can be used for resuming
the count.
相關PDF資料
PDF描述
S1C6S2L7D 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58
S1C6S2A7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2B7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2N7D 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC58
S1C6S2N7F0A0100 MICROCONTROLLER, PQFP60
相關代理商/技術參數
參數描述
S1C-6-S 制造商:GRIPCO 功能描述:
S1C7309X 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C7309X01 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C88349 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88649 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer