- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C6F567D0A0100 MICROCONTROLLER, UUC141 PDF資料下載
參數資料
| 型號： | S1C6F567D0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, UUC141 |
| 封裝： | DIE-141 |
| 文件頁數： | 200/208頁 |
| 文件大?。?/td> | 1561K |
| 代理商： | S1C6F567D0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁當前第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁
S1C6F567 TECHNICAL MANUAL
EPSON
83
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
(4) Parity bit selection
When checking and adding parity bits, write "1" into the parity enable register EPR to set to "with
parity check". As a result of this setting, in the 7-bit asynchronous mode, it has a 7 bits data +
parity bit configuration and in the 8-bit asynchronous mode it has an 8 bits data + parity bit
configuration.In this case, parity checking for receiving and adding a party bit for transmitting is
done automatically in hardware. Moreover, when "with parity check" has been selected, "odd" or
"even" parity must be further selected in the parity mode selection register PMD.
When "0" is written to the PMD register to select "without parity check" in the 7-bit asynchronous
mode, data configuration is set to 7 bits data (no parity) and in the 8-bit asynchronous mode (no
parity) it is set to 8 bits data (no parity) and parity checking and parity bit adding will not be done.
(5) Clock source selection
Select the clock source by writing data to the two bits of the clock source selection registers SCS0
and SCS1. (See Table 4.11.4.1.)
(6) Clock source control
When the programmable timer is selected for the clock source, set transfer rate on the programma-
ble timer side. (See "4.10 Programmable Timer".)
When the divided signal of OSC3 oscillation circuit is selected for the clock source, be sure that the
OSC3 oscillation circuit is turned ON prior to commencing data transfer. (See "4.3 Oscillation
Circuit".)
Data transmit procedure
The control procedure and operation during transmitting is as follows.
(1) Write "0" in the transmit enable register TXEN to reset the
serial interface.
(2) Write "1" in the transmit enable register TXEN to set into
the transmitting enable status.
(3) Write the transmitting data into TRXD0–TRXD7.
Also, when 7-bit data is selected, the TRXD7 data be-
comes invalid.
(4) Write "1" in the transmit control bit TXTRG and start
transmitting.
This control causes the shift clock to change to enable and
a start bit (LOW) is output to the SOUT terminal in
synchronize to its rising edge. The transmitting data set
to the shift register is shifted one bit at a time at each
rising edge of the clock thereafter and is output from the
SOUT terminal. After the data output, it outputs a stop
bit (HIGH) and HIGH level is maintained until the next
start bit is output.
The transmitting complete interrupt factor flag ISTR is set
to "1" at the point where the data transmitting is com-
pleted. When interrupt has been enabled, a transmitting
complete interrupt is generated at this point.
Set the following transmitting data using this interrupt.
(5) Repeat steps (3) to (4) for the number of bytes of trans-
mitting data, and then set the transmit disable status by
writing "0" to the transmit enable register TXEN, when
the transmitting is completed.
Data transmitting
End
TXEN
← 0
No
Yes
Transmit complete ?
Set transmitting data
to TRXD0–TRXD7
No
Yes
ISTR = 1 ?
TXEN
← 0
TXTRG
← 1
TXEN
← 1
Fig. 4.11.7.2 Transmit procedure in
asynchronous mode
相關PDF資料 |
PDF描述 |
|---|---|
| S1C6N3B0D0A0100 | MICROCONTROLLER, UUC54 |
| S1C6P366D0A0100 | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
| S1C6S2L7D | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58 |
| S1C6S2A7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C-6-S | 制造商:GRIPCO 功能描述: |
| S1C7309X | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C7309X01 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C88349 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88649 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。