- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C6F567D0A0100 MICROCONTROLLER, UUC141 PDF資料下載
參數資料
| 型號： | S1C6F567D0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, UUC141 |
| 封裝： | DIE-141 |
| 文件頁數： | 199/208頁 |
| 文件大小： | 1561K |
| 代理商： | S1C6F567D0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁當前第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁
82
EPSON
S1C6F567 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
4.11.7 Operation of asynchronous transfer
Asynchronous transfer is a mode that transfers by adding a start bit and a stop bit to the front and the
back of each piece of serial converted data. In this mode, there is no need to use a clock that is fully
synchronized clock on the transmit side and the receive side, but rather transmission is done while
adopting the synchronization at the start/stop bits that have attached before and after each piece of data.
The RS-232C interface functions can be easily realized by selecting this transfer mode.
This interface has separate transmit and receive shift registers and is designed to permit full duplex
transmission to be done simultaneously for transmitting and receiving.
For transfer data in the 7-bit asynchronous mode, either 7 bits data (no parity) or 7 bits data + parity bit
can be selected. In the 8-bit asynchronous mode, either 8 bits data (no parity) or 8 bits data + parity bit
can be selected.
Parity can be even or odd, and parity checking of received data and adding a party bit to transmitting
data will be done automatically. Thereafter, it is not necessary to be conscious of parity itself in the
program.
The start bit and stop bit are respectively fixed at one bit and data is transmitted and received by placing
the LSB (bit 0) at the front.
Sampling
clock
8bit data
D0 D1 D2 D3 D4 D5 D6
p
s1
s2
7bit data
+parity
D0 D1 D2 D3 D4 D5 D6 D7
s1
s2
8bit data
+parity
D0 D1 D2 D3 D4 D5 D6 D7
s1
p
s2
s1
s2
p
: Start bit (Low level, 1 bit)
: Stop bit (High level, 1 bit)
: Parity bit
7bit data
D0 D1 D2 D3 D4 D5 D6
s1
s2
Fig. 4.11.7.1 Transfer data configuration for asynchronous system
Here following, we will explain the control sequence and operation for initialization and transmitting /
receiving in case of asynchronous data transfer. See "4.11.8 Interrupt function" for the serial interface
interrupts.
Initialization of serial interface
The below initialization must be done in cases of asynchronous system transfer.
(1) Setting of transmitting/receiving disable
To set the serial interface into a status in which both transmitting and receiving are disabled, "0"
must be written to both the transmit enable register TXEN and the receive enable register RXEN.
Fix these two registers to a disable status until data transfer actually begins.
(2) Port selection
Because serial interface input/output terminals SIN and SOUT are set as I/O port terminals P10
and P11 at initial reset, "1" must be written to the serial interface enable register ESIF in order to set
these terminals for serial interface use.
SCLK and SRDY terminals set in the clock synchronous mode are not used in the asynchronous
mode. These terminals function as I/O port terminals P12 and P13.
(3) Setting of transfer mode
Select the asynchronous mode by writing the data as indicated below to the two bits of the mode
selection registers SMD0 and SMD1.
7-bit mode: SMD0 = "0", SMD1 = "1"
8-bit mode: SMD0 = "1", SMD1 = "1"
相關PDF資料 |
PDF描述 |
|---|---|
| S1C6N3B0D0A0100 | MICROCONTROLLER, UUC54 |
| S1C6P366D0A0100 | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
| S1C6S2L7D | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58 |
| S1C6S2A7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C-6-S | 制造商:GRIPCO 功能描述: |
| S1C7309X | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C7309X01 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C88349 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88649 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。