- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63406F 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128 PDF資料下載
參數資料
| 型號： | S1C63406F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128 |
| 封裝： | PLASTIC, TQFP15-128 |
| 文件頁數： | 47/144頁 |
| 文件大小： | 1160K |
| 代理商： | S1C63406F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁
132
EPSON
S1C63406 TECHNICAL MANUAL
APPENDIX S5U1C63000P MANUAL (PERIPHERAL CIRCUIT BOARD FOR S1C63406)
(3) Functional precautions
<LCD power supply circuit>
There is a finite delay time from the point at which the LCD power supply circuit (LPWR) turns on
until an LCD drive waveform is output. On this board, this delay is set to approx. 125 msec, which
differs from that of the actual IC.
<SVD circuit>
- Although the S1C63406 has a function for detecting externally sourced voltages, this board is unable
to detect externally sourced voltages. The SVD function is realized by artificially varying the power
supply voltage using the VSVD control on this board.
- There is a finite delay time from when the power to the SVD circuit turns on until actual detection of
the voltage. On this board, this delay is set to 61–92 sec, which differs from that of the actual IC.
Refer to Section 4.12, "SVD Circuit", when setting the appropriate wait time for the actual IC.
<Oscillation circuit>
-A wait time is required before oscillation stabilizes after the OSC3 oscillation control circuit (OSCC)
is turned on. On this board, even when OSC3 oscillation is changed (CLKCHG) without a wait time,
OSC3 will function normally. Refer to Section 4.3, "Oscillation Circuit", when setting the appropriate
wait time for the actual IC.
- Use separate instructions to switch the clock from OSC3 to OSC1 and to turn off the OSC3 oscillation
circuit. If executed simultaneously with a single instruction, these operations, although good with
this board, may not function properly well with the actual IC.
- Because the logic level of the oscillation circuit is high, the timing at which the oscillation starts on
this board differs from that of the actual IC.
- This board contains oscillation circuits for OSC1 and OSC3. Keep in mind that even though the
actual IC may not have a resonator connected to its OSC3, its emulator can operate with the OSC3
circuit.
- It is necessary to select the appropriate operating voltage for the internal circuits before the OSC3
oscillation circuit can be turned on in the actual IC. Be aware that this board can operate normally
even if an illegal voltage is selected.
-When using an external clock for OSC3, adjust the amplitude of the clock to 3.3 V
± 5% and the duty
ratio to 50%
± 10%, and input it to the ECLK3 pin with VSS as the ground.
<Access to undefined address space>
If any undefined space in the S1C63406's internal ROM/RAM or I/O is accessed for data read or write
operations, the read/written value is indeterminate. Additionally, it is important to remain aware that
indeterminate state differs between this board and the actual IC. Note that the ICE (S5U1C63000H1/
S5U1C63000H2) incorporates the program break function caused by accessing to an undefined
address space.
<Reset circuit>
Keep in mind that the operation sequence from when the ICE and this board are powered on until the
time at which the program starts running differs from the sequence from when the actual IC is
powered on till the program starts running. This is because this board becomes capable of operating
as a debugging system after the user program and optional data are downloaded. When operating the
ICE after placing it in free-running mode, always apply a system reset. A system reset can be per-
formed by pressing the reset switch on this board, by a reset pin input, or by holding the input ports
low simultaneously.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63408F0A0100 | MICROCONTROLLER, PQFP128 |
| S1C63406D0A0100 | MICROCONTROLLER, UUC103 |
| S1C63455F | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128 |
| S1C63455D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 |
| S1C63458F0A0100 | MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。