參數資料
型號: S1C63406F
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128
封裝: PLASTIC, TQFP15-128
文件頁數: 45/144頁
文件大?。?/td> 1160K
代理商: S1C63406F
S1C63406 TECHNICAL MANUAL
EPSON
131
APPENDIX S5U1C63000P MANUAL (PERIPHERAL CIRCUIT BOARD FOR S1C63406)
A.3 Usage Precautions
To ensure correct use of this board (S5U1C63000P), please observe the following precautions.
A.3.1 Operational precautions
(1) Before inserting or removing cables, turn off power to all pieces of connected equipment.
(2) Do not turn on power or load mask option data if all of the input ports (K00–K03) are held low. Doing
so may activate the multiple key entry reset function.
(3) Before debugging, always be sure to load mask option data.
A.3.2 Differences with the actual IC
(1) Differences in I/O
<Interface power supply>
This board and target system interface voltage is set to +3.3 V. To obtain the same interface voltage as
in the actual IC, attach a level shifter circuit, etc. on the target system side to accommodate the
required interface voltage.
<Each output port’s drive capability>
The drive capability of each output port on this board is higher than that of the actual IC. When
designing application system and software, refer to Chapter 7, "Electrical Characteristics", to confirm
each output port’s drive capability.
<Each port’s protective diode>
All I/O ports incorporate a protective diode for VDD and VSS, and the interface signals between this
board and the target system are set to +3.3 V. Therefore, this board and the target system cannot be
interfaced with voltages exceeding VDD by setting the output ports for open-drain mode.
<Pull-up resistance value>
The pull-up resistance values on this board are set to 220 k
which differ from those for the actual IC.
For the resistance values on the actual IC, refer to Chapter 7, "Electrical Characteristics".
Note that when using pull-up resistors to pull the input pins high, the input pins may require a
certain period to reach a valid high level. Exercise caution if a key matrix circuit is configured using a
combination of output and input ports, since rise delay times on these input ports differ from those of
the actual IC.
(2) Differences in current consumption
The amount of current consumed by this board differs significantly from that of the actual IC. Inspect-
ing the LEDs on this board may help you keep track of approximate current consumption. The
following factors/components greatly affect device current consumption:
<Those which can be verified by LEDs and monitor pins>
a) Run and Halt execution ratio (verified by LEDs and monitor pins on the ICE)
b) CPU operating voltage change (VDC0, VDC1)
c) OSC3 oscillation on/off (OSCC)
d) CPU clock change (CLKCHG)
e) SVD circuit on/off (SVDON)
f) Heavy load protection mode (HLMOD)
g) LCD power supply on/off (LPWR)
h) LCD constant-voltage change (VCCHG)
<Those that can only be counteracted by system or software>
i) Current consumed by the internal pull-up resistors
j) Input ports in a floating state
相關PDF資料
PDF描述
S1C63408F0A0100 MICROCONTROLLER, PQFP128
S1C63406D0A0100 MICROCONTROLLER, UUC103
S1C63455F 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128
S1C63455D 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105
S1C63458F0A0100 MICROCONTROLLER, PQFP144
相關代理商/技術參數
參數描述
S1C63408 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63557D04Q000 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT
S1C63567 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer