參數資料
型號： S1C63406F
元件分類： 微控制器/微處理器
英文描述： 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128
封裝： PLASTIC, TQFP15-128
文件頁數： 121/144頁
文件大小： 1160K
代理商： S1C63406F
70
EPSON
S1C63406 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Programmble Timer)
PTRST0: Timer 0 reset (reload) (FFC2HD1)
PTRST1: Timer 1 reset (reload) (FFC3HD1)
Resets the timer and presets reload data to the counter.
When "1" is written: Reset
When "0" is written: No operation
Reading: Always "0"
By writing "1" to PTRST0, the reload data in the reload register PLD00–PLD07 is preset to the counter in
timer 0. Similarly, the reload data in PLD10–PLD17 is preset to the counter in timer 1 by PTRST1.
When the counter is preset in the RUN status, the counter restarts immediately after presetting. In the
case of STOP status, the reload data is preset to the counter and is maintained.
No operation results when "0" is written.
Since these bits are exclusively for writing, always set to "0" during reading.
PTRUN0: Timer 0 RUN/STOP control register (FFC2HD0)
PTRUN1: Timer 1 RUN/STOP control register (FFC3HD0)
Controls the RUN/STOP of the counter.
When "1" is written: RUN
When "0" is written: STOP
Reading: Valid
The counter in timer 0 starts counting down by writing "1" to the PTRUN0 register and stops by writing
"0".
In STOP status, the counter data is maintained until the counter is reset or is set in the next RUN status.
When STOP status changes to RUN status, the data that has been maintained can be used for resuming
the count.
Same as above, the timer 1 counter is controlled by the PTRUN1 register.
At initial reset, these registers are set to "0".
CHSEL: TOUT output channel selection register (FFC1HD3)
Selects the channel used for TOUT signal output.
When "1" is written: Timer 1
When "0" is written: Timer 0
Reading: Valid
This register selects which timer's underflow (timer 0 or timer 1) is used to generate a TOUT signal. When
"0" is written to the CHSEL register, timer 0 is selected and when "1" is written, timer 1 is selected. In the
16-bit
× 2 channels mode (MODE16 = "1"), timer 1 is always selected regardless of this register setting.
At initial reset, this register is set to "0".
PTOUT: TOUT output control register (FFC1HD2)
Turns TOUT signal output ON and OFF.
When "1" is written: ON
When "0" is written: OFF
Reading: Valid
PTOUT is the output control register for the TOUT signal. When "1" is written to the register, the TOUT
signal is output from the R12 terminal and when "0" is written, the terminal goes high (VDD) level.
However, the data register R12 must always be "1".
At initial reset, this register is set to "0".
相關PDF資料
PDF描述
S1C63408F0A0100 MICROCONTROLLER, PQFP128
S1C63406D0A0100 MICROCONTROLLER, UUC103
S1C63455F 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128
S1C63455D 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105
S1C63458F0A0100 MICROCONTROLLER, PQFP144
相關代理商/技術參數
參數描述
S1C63408 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63557D04Q000 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT
S1C63567 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*