- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63406F 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128 PDF資料下載
參數資料
| 型號： | S1C63406F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128 |
| 封裝： | PLASTIC, TQFP15-128 |
| 文件頁數： | 138/144頁 |
| 文件大小： | 1160K |
| 代理商： | S1C63406F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁當前第138頁第139頁第140頁第141頁第142頁第143頁第144頁
S1C63406 TECHNICAL MANUAL
EPSON
85
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
Receive error
During receiving the following three types of errors can be detected by an interrupt.
(1) Parity error
When writing "1" to the EPR register to select "with parity check", a parity check (vertical parity
check) is executed during receiving. After each data bit is sent a parity check bit is sent. The parity
check bit is a "0" or a "1". Even parity checking will cause the sum of the parity bit and the other
bits to be even. Odd parity causes the sum to be odd. This is checked on the receiving side.
The parity check is performed when data received in the shift register is transferred to the receive
data buffer. It checks whether the parity check bit is a "1" or a "0" (the sum of the bits including the
parity bit) and the parity set in the PMD register match. When it does not match, it is recognized
as an parity error and the parity error flag PER and the error interrupt factor flag ISER is set to "1".
When interrupt has been enabled, an error interrupt is generated at this point.
The PER flag is reset to "0" by writing "1".
Even when this error has been generated, the received data corresponding to the error is trans-
ferred in the receive data buffer and the receive operation also continues.
The received data at this point cannot assured because of the parity error.
(2) Framing error
In asynchronous transfer, synchronization is adopted for each character at the start bit ("0") and
the stop bit ("1"). When receiving has been done with the stop bit set at "0", the serial interface
judges the synchronization to be off and a framing error is generated. When this error is gener-
ated, the framing error flag FER and the error interrupt factor flag ISER are set to "1". When
interrupt has been enabled, an error interrupt is generated at this point.
The FER flag is reset to "0" by writing "1".
Even when this error has been generated, the received data for it is loaded into the receive data
buffer and the receive operation also continues. However, even when it does not become a framing
error with the following data receipt, such data cannot be assured.
Even when this error has been generated, the received data corresponding to the error is trans-
ferred in the receive data buffer and the receive operation also continues. However, even when it
does not become a framing error with the following data receiving, such data cannot be assured.
(3) Overrun error
When the next data is received before "1" is written to RXTRG, an overrun error will be generated,
because the previous receive data will be overwritten. When this error is generated, the overrun
error flag OER and the error interrupt factor flag ISER are set to "1". When interrupt has been
enabled, an error interrupt is generated at this point. The OER flag is reset to "0" by writing "1"
into it.
Even when this error has been generated, the received data corresponding to the error is trans-
ferred in the receive data buffer and the receive operation also continues.
Furthermore, when the timing for writing "1" to RXTRG and the timing for the received data
transfer to the receive data buffer overlap, it will be recognized as an overrun error.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63408F0A0100 | MICROCONTROLLER, PQFP128 |
| S1C63406D0A0100 | MICROCONTROLLER, UUC103 |
| S1C63455F | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128 |
| S1C63455D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 |
| S1C63458F0A0100 | MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。