- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63406F 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128 PDF資料下載
參數資料
| 型號： | S1C63406F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128 |
| 封裝： | PLASTIC, TQFP15-128 |
| 文件頁數： | 20/144頁 |
| 文件大?。?/td> | 1160K |
| 代理商： | S1C63406F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁
108
EPSON
S1C63406 TECHNICAL MANUAL
Table 5.2.1 Time difference between ISER and ISRC on error generation
Clock source
Time difference
fOSC3 / n
Programmable timer
1/2 cycles of fOSC3 / n
1 cycle of timer 1 underflow
(5) When the demultiplied signal of the OSC3 oscillation circuit is made the clock source, it is necessary
to turn the OSC3 oscillation ON, prior to using the serial interface.
A time interval of 5 msec, from the turning ON of the OSC3 oscillation circuit to until the oscillation
stabilizes, is necessary, due to the oscillation element that is used. Consequently, you should allow an
adequate waiting time after turning ON of the OSC3 oscillation, before starting transmitting/receiv-
ing of serial interface. (The oscillation start time will vary somewhat depending on the oscillator and
on the externally attached parts. Refer to the oscillation start time example indicated in Chapter 7,
"Electrical Chracteristics".)
At initial reset, the OSC3 oscillation circuit is set to OFF status.
(6) Be aware that the maximum clock frequency for the serial interface is limited to 2 MHz.
SVD circuit
(1) To obtain a stable detection result, the SVD circuit must be ON for at least l00 sec. So, to obtain the
SVD detection result, follow the programming sequence below.
1. Set SVDON to "1"
2. Maintain for 100 sec minimum
3. Set SVDON to "0"
4. Read SVDDT
(2) The SVD circuit should normally be turned OFF because SVD operation increase current consump-
tion.
Heavy load protection function
Be aware that current consumption increases in the heavy load protection mode.
Interrupt
(1) The interrupt factor flags are set when the interrupt condition is established, even if the interrupt
mask registers are set to "0".
(2) After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag =
"1") is set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure
to reset (write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the
interrupt enabled state.
(3) After an initial reset, all the interrupts including NMI are masked until both the stack pointers SP1
and SP2 are set with the software. Be sure to set the SP1 and SP2 in the initialize routine.
Further, when re-setting the stack pointer, the SP1 and SP2 must be set as a pair. When one of them is
set, all the interrupts including NMI are masked and interrupts cannot be accepted until the other one
is set.
(4) When using the SLEEP function, set the following flag and the registers for the K0x port to be used to
cancel SLEEP status before executing the SLP instruction.
Interrupt flag (I flag) = "1" (interrupts are enabled)
Interrupt selection register SIK0x = "1" (the K0x input port interrupt is selected)
Interrupt mask register EIK0x = "1" (the K0x input port interrupt is enabled)
Noise rejector selection register K0NR1–K0NR0 = "00" (noise rejector is bypassed)
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63408F0A0100 | MICROCONTROLLER, PQFP128 |
| S1C63406D0A0100 | MICROCONTROLLER, UUC103 |
| S1C63455F | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128 |
| S1C63455D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 |
| S1C63458F0A0100 | MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。