- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C60L16F0A0100 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | S1C60L16F0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, QFP14-80 |
| 文件頁數： | 49/105頁 |
| 文件大?。?/td> | 841K |
| 代理商： | S1C60L16F0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁
38
EPSON
S1C60N16 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
SCTRG: Clock trigger (2E7HD3)
This is a trigger to start input/output of synchronous clock.
When "1" is written : Trigger
When "0" is written : No operation
Read-out : Always "0"
When this trigger is supplied to the serial interface activating circuit, the synchronous clock (SCLK)
input/output is started.
As a trigger condition, it is required that data writing or reading on data registers SD0–SD7 be performed
prior to writing "1" to SCTRG. (The internal circuit of the serial interface is initiated through data writ-
ing/reading on data registers SD0–SD7.)
Supply trigger only once every time the serial interface is placed in the RUN state. Refrain from perform-
ing trigger input multiple times, as leads to malfunctioning.
Moreover, when the synchronous clock SCLK is external clock, start to input the external clock after the
trigger.
SIOF (R11): Serial interface status (2ECHD1)
Indicates the running status of the serial interface.
When "1" is read out : RUN status
When "0" is read out : STOP status
Writing : Invalid
The RUN status is indicated from immediately after "1" is written to SCTRG bit through to the end of
serial data input/output.
The SIOF read only bit can be used only when the R11 port is configured for SIOF output by mask option.
4.7.6 Programming notes
(1) If the bit data of SE2 changes while the serial interface is in the master mode, a hazard will be output
to the SCLK (P12) terminal. If this poses a problem for the system, be sure to set the SCLK to the
external clock if the bit data of SE2 is to be changed.
(2) Be sure that read-out of the interrupt factor flag (ISIO) is done only when the serial port is in the STOP
status (SIOF = "0") and the DI status (interrupt flag = "0"). If read-out is performed while the serial
data is in the RUN status (during input or output), the data input or output will be suspended and the
initial status resumed. Read-out during the EI status (interrupt flag = "1") causes malfunctioning.
(3) When using the serial interface in the master mode, the synchronous clock uses the CPU system clock.
Accordingly, do not change the system clock (fOSC1
fOSC3) while the serial interface is operating.
(4) Perform data writing/reading to data registers SD0–SD7 only while the serial interface is halted (i.e.,
the synchronous clock is neither being input or output).
(5) As a trigger condition, it is required that data writing or reading on data registers SD0–SD7 be per-
formed prior to writing "1" to SCTRG. (The internal circuit of the serial interface is initiated through
data writing/reading on data registers SD0–SD7.) Supply trigger only once every time the serial
interface is placed in the RUN state. Moreover, when the synchronous clock SCLK is external clock,
start to input the external clock after the trigger.
(6) Be sure that writing to the interrupt mask register is done only in the DI status (interrupt flag = "0").
Writing to the interrupt mask register while in the EI status (interrupt flag = "1") may cause malfunc-
tion.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C60N01F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP48 |
| S1C60N02D | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC52 |
| S1C60L02 | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C60N04D | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48 |
| S1C60N08D | 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, UUC96 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C60N05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60R08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63004 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。