參數資料
型號: PSD854F2A-90MT
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 256K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP52
封裝: ROHS COMPLIANT, PLASTIC, QFP-52
文件頁數: 93/128頁
文件大?。?/td> 1045K
代理商: PSD854F2A-90MT
PSD8XXFX
I/O ports
Doc ID 7833 Rev 7
16
I/O ports
There are four programmable I/O ports: ports A, B, C, and D. Each of the ports is eight bits
except port D, which is 3 bits. Each port pin is individually user configurable, thus allowing
multiple functions per port. The ports are configured using PSDsoft Express Configuration
or by the MCU writing to on-chip registers in the CSIOP space.
The topics discussed in this section are:
General port architecture
Port operating modes
Port configuration registers (PCR)
Port Data registers
Individual port functionality.
16.1
General port architecture
The general architecture of the I/O port block is shown in Figure 25. Individual port
architectures are shown in Figure 27, Figure 28, Figure 29, and Figure 30. In general, once
the purpose for a port pin has been defined, that pin is no longer available for other
purposes. Exceptions are noted.
As shown in Figure 25, the ports contain an output multiplexer whose select signals are
driven by the configuration bits in the Control registers (Ports A and B only) and PSDsoft
Express Configuration.Inputs to the multiplexer include the following:
Output data from the Data Out register
Latched address outputs
CPLD macrocell output
External Chip Select (ECS0-ECS2) from the CPLD.
The port Data Buffer (PDB) is a tri-state buffer that allows only one source at a time to be
read. The port Data Buffer (PDB) is connected to the Internal data bus for feedback and can
be read by the MCU. The Data Out and macrocell outputs, Direction and Control registers,
and port pin input are all connected to the port data buffer (PDB).
The port pin’s tri-state output driver enable is controlled by a two input OR gate whose
inputs come from the CPLD AND Array enable product term and the Direction register. If the
enable product term of any of the Array outputs are not defined and that port pin is not
defined as a CPLD output in the PSDabel file, then the Direction register has sole control of
the buffer that drives the port pin.
The contents of these registers can be altered by the MCU. The port Data Buffer (PDB)
feedback path allows the MCU to check the contents of the registers.
Ports A, B, and C have embedded input macrocells (IMC). The input macrocells (IMC) can
be configured as latches, registers, or direct inputs to the PLDs. The latches and registers
are clocked by Address Strobe (ALE/AS, PD0) or a product term from the PLD AND Array.
The outputs from the input macrocells (IMC) drive the PLD input bus and can be read by the
相關PDF資料
PDF描述
PSD854F2A-90UT 256K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP64
PSH665-FREQ-OUT1 VCXO, SINE OUTPUT, 465 MHz - 865 MHz
PSM3-022K 1 ELEMENT, 0.022 uH, GENERAL PURPOSE INDUCTOR, SMD
PSM3-068K 1 ELEMENT, 0.068 uH, GENERAL PURPOSE INDUCTOR, SMD
PSM3-120K 1 ELEMENT, 0.12 uH, GENERAL PURPOSE INDUCTOR, SMD
相關代理商/技術參數
參數描述
PSD854F2V-12JI 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 120ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD854F2V-12MI 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 120ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD854F2V-90J 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD854F2V-90M 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD-8M-01 制造商:Richco 功能描述:CB SPT REST MNT NAT 8MM SPC