參數資料
型號: PSD854F2A-90MT
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 256K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP52
封裝: ROHS COMPLIANT, PLASTIC, QFP-52
文件頁數: 42/128頁
文件大小: 1045K
代理商: PSD854F2A-90MT
PSD architectural overview
PSD8XXFX
Doc ID 7833 Rev 7
3
PSD architectural overview
PSD devices contain several major functional blocks. Figure 4 shows the architecture of the
PSD device family. The functions of each block are described briefly in the following
sections. Many of the blocks perform multiple functions and are user configurable.
3.1
Memory
Each of the memory blocks is briefly discussed in the following paragraphs. A more detailed
discussion can be found in Section 6.1: Memory blocks.
The 1 Mbit or 2 Mbit (128K x 8, or 256K x 8) Flash memory is the primary memory of the
PSD. It is divided into 8 equally-sized sectors that are individually selectable.
The optional 256 Kbit (32K x 8) secondary Flash memory is divided into 4 equally-sized
sectors. Each sector is individually selectable.
The optional SRAM is intended for use as a scratch-pad memory or as an extension to the
MCU SRAM.
Each sector of memory can be located in a different address space as defined by the user.
The access times for all memory types includes the address latching and DPLD decoding
time.
3.2
Page register
The 8-bit Page register expands the address range of the MCU by up to 256 times. The
paged address can be used as part of the address space to access external memory and
peripherals, or internal memory and I/O. The Page register can also be used to change the
address mapping of sectors of the Flash memories into different memory spaces for IAP.
3.3
PLDs
The device contains two PLDs, the Decode PLD (DPLD) and the Complex PLD (CPLD), as
shown in Table 4, each optimized for a different function. The functional partitioning of the
PLDs reduces power consumption, optimizes cost/performance, and eases design entry.
The DPLD is used to decode addresses and to generate Sector Select signals for the PSD
internal memory and registers. The DPLD has combinatorial outputs. The CPLD has 16
Output macrocells (OMC) and 3 combinatorial outputs. The PSD also has 24 input
macrocells (IMC) that can be configured as inputs to the PLDs. The PLDs receive their
inputs from the PLD input bus and are differentiated by their output destinations, number of
product terms, and macrocells.
The PLDs consume minimal power. The speed and power consumption of the PLD is
controlled by the Turbo Bit in PMMR0 and other bits in the PMMR2. These registers are set
by the MCU at run-time. There is a slight penalty to PLD propagation time when invoking the
power management features.
相關PDF資料
PDF描述
PSD854F2A-90UT 256K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP64
PSH665-FREQ-OUT1 VCXO, SINE OUTPUT, 465 MHz - 865 MHz
PSM3-022K 1 ELEMENT, 0.022 uH, GENERAL PURPOSE INDUCTOR, SMD
PSM3-068K 1 ELEMENT, 0.068 uH, GENERAL PURPOSE INDUCTOR, SMD
PSM3-120K 1 ELEMENT, 0.12 uH, GENERAL PURPOSE INDUCTOR, SMD
相關代理商/技術參數
參數描述
PSD854F2V-12JI 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 120ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD854F2V-12MI 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 120ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD854F2V-90J 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD854F2V-90M 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD-8M-01 制造商:Richco 功能描述:CB SPT REST MNT NAT 8MM SPC